Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
F70 adjustable front locking devices give F70 drawer runners a dedicated front locking point, so the runner engages securely and holds alignment during everyday use and repeated openings. The Salice America design with dual steel/plastic construction creates a rigid locking structure where steel carries the load and plastic manages the interface, which helps keep movement controlled while limiting wear in the contact areas. This vertical mount, left and right front locking device format matches common drawer layouts, so each side locks in the same way and supports consistent fit from cabinet to cabinet. The UBF70CLIP-VLR part number ties directly to the F70 runner family, which matters when matching new installations or coordinating with existing progressa F70 hardware in a shop standard.
The F70 vertical mount front locking device uses tool free lateral and depth adjustments so drawer fronts can be shifted side-to-side and in-out directly at the clip, reducing the time spent loosening fasteners and re-squaring fronts. Overhang must be 13 mm (1/2 inch), which sets a clear dimension for the drawer front projection at design and layout, helping casework planners size fronts correctly for the F70 system. Pre-drilling is recommended at 2.5 mm (3/32 inch), giving installers a defined bit size that supports accurate pilot holes and reliable screw grip in typical cabinet materials. By aligning to all F70 runner versions, the same adjustment method and mounting expectations carry across a full bank of drawers, which simplifies workflow when several cabinets are installed in a single run.
The F70 vertical mount front locking device is specified for all F70 runner versions, so it fits projects that standardize around the Salice America progressa F70 slide platform. In banks of drawers that share this runner family, using the UBF70CLIP-VLR on each side gives the same locking geometry across upper and lower drawers, which supports consistent reveals along a tall cabinet. The 13 mm (1/2 inch) overhang requirement defines how far the drawer front projects relative to the box, so shops building face frame or frameless cabinets can design fronts around that fixed measurement and avoid trial-and-error adjustments at installation. Because the device is described as left and right front locking, one solution handles both sides of the drawer, which keeps part planning straightforward when scheduling multiple jobs using the same F70 hardware.
The built-in tool free lateral and depth adjustments allow the installer to move the drawer front horizontally and in depth directly through the F70 locking device, which matters when aligning narrow gaps, tall drawer stacks, or doors next to drawers. Without reaching for tools, the front can be nudged to match adjacent fronts, so final alignment can be completed quickly after cabinets are fixed in place. Dual steel/plastic construction contributes to these adjustments holding over time because the steel elements support structural loads while the plastic portions guide movement, helping the clip keep its set position through repeated drawer use. Pre-drilling at 2.5 mm (3/32 inch) creates pilot holes sized to the hardware expectation, which supports stable mounting so the set lateral and depth positions are maintained rather than drifting as the drawer is cycled.
The F70 adjustable front locking devices are specified for all F70 runner versions, so any drawer using an F70 runner from Salice America can use this clip to lock the front to the slide.
The vertical mount layout places the locking device at the front of the drawer in a consistent orientation, creating a repeatable reference so engagement with the F70 runner matches from cabinet to cabinet.
The F70 front locking device offers tool free lateral and depth adjustments, letting installers shift the drawer front sideways and in or out at the clip to refine alignment with neighboring fronts.
The F70 locking device states that overhang must be 13 mm, or 1/2 inch, which sets the drawer front projection dimension so cabinets can be designed and built to that F70 standard.
The Salice F70 front locking device lists pre-drilling at 2.5 mm, or 3/32 inch, which defines a pilot size that supports reliable screw grip when fastening into typical cabinet materials.
The dual steel/plastic construction lets steel carry structural loads while plastic interfaces manage engagement, supporting firm locking of the drawer front and controlled movement with the F70 runner system.
The F70 adjustable front locking devices are identified as UBF70CLIP-VLR for left and right vertical mounting on all F70 runner versions, so they align with Salice America progressa F70 drawer designs already in your shop standards. Dual steel/plastic construction, 13 mm (1/2 inch) overhang requirement, and tool free lateral and depth adjustments turn the device into a defined interface that supports both structural locking and precise front alignment. For drawer runs built around the F70 platform, this front locking device keeps hardware selection tied to a single, documented part while supporting efficient installation and adjustment on site.
Sold In: 1 Set