Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Salice angle restriction clip limits the opening angle of compatible Salice hinges, so a cabinet door stops at a controlled position during use. The clip is a hinge angle restriction clip in white, giving a discreet solution when you need to prevent a door from opening too far inside a cabinet run or against an adjacent surface. As a stop device only, it works with Salice 100 Series and 700 Series hinges, so you can match it to existing hardware in the same cabinet line. The SAP description "84DEG ANGLE RESTRICTIOIN CLIP" reflects its role as a restriction component, which matters when you are selecting parts by code for repeat jobs. With a manufacturer part number S1E637XY and a listing under Hinge Angle Restriction Clips, it is easy to specify and reorder consistently across projects.
The clip limits the opening angle to approximately 86 degrees, so during installation you can predict the final door swing and position cabinets or adjacent panels accordingly. On Salice 100 Series hinges, the documented change from 105 degrees to 86 degrees gives a clear before-and-after reference when adjusting layouts in existing runs. On Salice 700 Series hinges, the shift from 110 degrees to 86 degrees allows a consistent stop position across cabinets that might otherwise open at different angles. Because this part is categorized as a hinge angle restriction clip and described as a stop device only, it plays a defined role in the hinge system and supports straightforward planning when laying out door clearances on new or retrofit jobs.
The web description specifies that this clip provides angle restriction on Salice 100 Series hinges from 105 degrees to 86 degrees, which matters when these hinges are already standard in your cabinet program and you need to adapt only certain doors. The same description states that it provides angle restriction on Salice 700 Series hinges from 110 degrees down to 86 degrees, allowing a consistent stop angle even on hinges that were originally chosen for wider opening. Because the part is identified as a hinge angle restriction clip for the Series 100 and 700 families, it fits into projects using these lines where you want controlled access at corners, near walls, or beside tall panels while keeping the base hinge model in place.
The clip limits the opening angle to approximately 86 degrees, and that predictable stop supports repeatable cabinet door behavior across a run, which is important for installers building banks of doors with tight reveals. As a stop device only with hinges sold separately, it leaves your hinge specification unchanged while adding a layer of control to the motion, which helps standardize door swing without redesigning hardware schedules. The SAP description "84DEG ANGLE RESTRICTIOIN CLIP" and manufacturer part number S1E637XY identify a specific restriction point, which simplifies communication between shop drawings, purchasing, and site installation. The product name notes the Series 100 and 700 use and the white finish, tying visual expectations to functional behavior, so completed installations match both design intent and opening limits.
The clip limits the opening angle to approximately 86 degrees, so the door stops short of the hinge's full range and reduces the risk of contact with nearby doors, walls, or panels.
On Salice 100 Series hinges, the clip changes the opening angle from 105 degrees to 86 degrees, which tightens the door swing envelope for corner cabinets or close-spaced doors.
On Salice 700 Series hinges, the clip changes the opening angle from 110 degrees to 86 degrees, so wider-opening doors now stop at a consistent controlled angle.
The hinge angle restriction clip functions as a stop device only, working with Salice hinges to define the maximum opening angle while the hinge handles normal motion and mounting.
The product is described as white, so it tends to blend with light cabinet interiors, keeping the restriction component visually unobtrusive when the door is opened.
Packing is specified as 100 each per box and it is sold in both broken and full box quantities, so purchasing can match project size from small repairs to larger runs.
This Salice angle restriction clip is described as limiting the opening angle to approximately 86 degrees and as a stop device only, so it serves projects where hinge choice is already established but door travel needs control. Documented changes from 105 degrees to 86 degrees on Salice 100 Series and from 110 degrees to 86 degrees on Salice 700 Series give clear planning values for layout work. With the SAP description "84DEG ANGLE RESTRICTIOIN CLIP," the Series 100 and 700 naming, and the manufacturer part number S1E637XY, this white hinge angle restriction clip can be specified by code and reused consistently across jobs requiring predictable cabinet door swing.
Sold In: 1 Each