Coat and Hat Hook, 2" (51 mm) Length - Matte Nickel, Epco | CH101-ZMN-2

EPCO Coat And Hat Hook For Everyday Hanging

EPCO coat and hat hook provides a compact hanging point with a projection of 2 inches, so coats and hats sit off the mounting surface while keeping the hardware close to the wall for a clean look. The base length of 1-7/8 inch sets a short footprint that fits tight spots on cabinet ends, closet panels, or wall rails where space is limited. A base width of 3/4 inch concentrates the mounting area, which helps when positioning the hook between other decorative hardware on narrow stiles. The matte nickel finish defines the visual tone as a muted metallic, which works well where a low-sheen appearance is preferred over polished metal. Zamack material construction means the hook body is made from a cast metal alloy, giving it a solid feel in normal decorative hardware applications. Sold individually, it suits both single replacement jobs and matching runs across multiple cabinets or rooms.

Key Decorative Hook Details That Drive Use

• The 2 inch projection holds garments away from doors or panels, helping reduce scuff contact on finished wood or laminate surfaces during daily use.
• A 1-7/8 inch base length provides enough bearing area to distribute load across the mounting surface, which supports stable performance on typical cabinet or wall substrates.
• The 3/4 inch base width focuses the hook footprint, allowing placement on narrow rails or stiles without crowding adjacent hardware layouts.
• Matte nickel finish delivers a subdued metallic tone, which helps the hook blend with other matte nickel decorative hardware and trim on a project.
• Zamack metal construction offers a rigid casting for the hook body, supporting consistent geometry when laying out multiple hooks along a straight line.
• Classification as decorative hooks places this part within a coordinated hardware group, easing selection when matching hooks to other decorative hardware and moldings.

Mounting Dimensions That Support Straightforward Layout

The base length of 1-7/8 inch and base width of 3/4 inch define a compact rectangle, giving clear reference points when marking hole locations on cabinets, closet panels, or wall backers. With a 2 inch projection, the hook extends far enough to carry typical coats and hats while remaining short enough to avoid deep intrusion into walkways or cabinet interiors. The matte nickel finish on the visible surfaces sets a consistent appearance, which helps maintain a uniform look when several hooks are installed in a row. Zamack construction creates a single-piece body, so the installer works with a stable form that stays aligned against the mounting surface while fasteners are tightened.

Using This Matte Nickel Hook In Real Projects

Where This Decorative Hook Works Best

As a decorative hook within the Decorative Hardware and Moldings category, this part suits projects where visual coordination matters alongside function, such as cabinet sides, mudroom panels, or office coat stations. The 2 inch projection gives enough stand-off to hang a coat over a hat or scarf without the fabric pressing flat against the wood, which helps garments dry and keeps finishes visible. With its 1-7/8 inch base length, the hook fits neatly on short rails or end panels common in cabinetry, providing hanging points without competing for space with pulls or knobs. The 3/4 inch base width lets it sit comfortably on narrow stile faces found in many woodworking applications, maintaining proportion so the hook does not overpower slimmer trim pieces. The matte nickel finish pairs naturally with other matte nickel decorative hardware, letting designers and installers maintain a consistent finish story across hinges, pulls, and hooks in the same room.

Why These Hook Details Support Consistent Results

The defined base length of 1-7/8 inch and base width of 3/4 inch make layout repeatable from hook to hook, which is useful when creating straight, evenly spaced rows along a wall or cabinet run. The 2 inch projection is a fixed, predictable dimension, so spacing between opposing hooks or between hooks and adjacent doors can be planned to prevent contact during typical swing or access. Zamack construction gives the hook a cast form with stable contours, helping each unit present the same profile when aligned visually across a project. The matte nickel finish helps mask minor handling marks during installation compared to highly polished surfaces, which supports a clean final appearance once the job is complete. Being sold as each, under EPCO part CH101-ZMN-2, simplifies ordering specific counts for custom layouts, reducing leftover decorative hardware when planning single rows or balanced pairs.

Common Questions About This EPCO Coat Hook

Select This Hook For Coordinated Hanging Points

Choose the EPCO CH101-ZMN-2 coat and hat hook when a 2 inch projection and compact 1-7/8 by 3/4 inch base suit your layout, and a matte nickel zamack decorative hook matches surrounding hardware across your cabinets or wall-mounted hanging runs.