Small oval corner rod kit gives a 90 degree oval closet rod section sized for tight closet corners, so hanging space can follow the corner instead of stopping short. The Epco KIT830-90-PC-SM design uses a 15mm wide by 30mm high oval profile, which creates a low-profile hanging surface that fits compact closet layouts while still presenting a stable bar for hangers. The 90 degree angle in the oval rod ties two runs together around a corner, which helps carry hanging loads across both sides instead of concentrating weight at a dead end. The rod wall thickness is 1 mm, so the tube stays light enough to handle and cut while still built as a formed oval section for everyday closet hanging use. Each side of the corner rod measures 11.5 inches long, giving a defined hanging span on both walls that suits small reach-in or return sections.
The Epco small oval corner rod kit uses oval under-shelf mounting, so the rod sits beneath a shelf rather than on sidewall sockets. Two oval under-shelf flanges support the ends, which places the 15mm by 30mm oval tube directly under fixed structure and helps define the rod height from the shelf underside. Two oval under-shelf center supports carry the interior span of the 11.5 inch sides, so weight along each leg of the 90 degree corner is shared between end and intermediate supports instead of relying only on the corners. Fasteners are provided with the hardware, so the flanges and center supports can be secured to the shelf or support surface using the matching attachment method straight from the kit.
This small oval corner rod kit suits closet layouts that turn a right-angle corner and need a 90 degree corner oval closet rod to keep hangers running continuously. The 11.5 inch length on each side fits shorter return walls, so installers can bridge between two closet rod runs without needing extra-long corner sections. The 15mm by 30mm oval closet rod profile works in closet systems laid out for oval tubing, keeping the cross-section consistent from straight runs through the corner piece. With under-shelf oval flanges and oval under-shelf center supports, the assembly is intended for closets that use a shelf-and-rod configuration, so the shelf above defines both support points and visual alignment along the wall. The polished chrome finish suits jobs where visible rods are part of the finished look, and the right-angle geometry helps line up garments neatly along both walls of the corner.
The 90 degree angle built into the oval corner closet rod removes the need to joint separate straight pieces at the corner, which avoids alignment issues at the bend and gives a smooth path for hangers around the turn. The 1 mm wall thickness and oval form combine to keep the tube light yet structurally shaped, which helps the rod carry normal closet loads while staying practical to cut to final length when trimming for a specific installation. Two oval under-shelf flanges locate the ends of the rod directly under the shelf, so the installer has defined bearing points that square the 15mm wide by 30mm high profile to the underside of the shelf. The two oval under-shelf center supports sit between these flanges on the 11.5 inch sides, so each leg of the corner shares load across multiple supports, limiting deflection under typical hanging conditions and maintaining straight sightlines. Fasteners in the kit match the flanges and center supports, which keeps attachment consistent at every support point along the corner section.
The Epco small oval corner rod kit uses a 15mm wide by 30mm high oval tube, and each side of the 90 degree corner section measures 11.5 inches in length.
The 90 degree corner oval closet rod carries hangers around a right-angle turn, so two walls of a closet can share continuous hanging space instead of ending at the corner.
The small oval corner rod kit uses oval under-shelf flanges at the ends and oval under-shelf center supports between them, so the rod mounts directly beneath a shelf surface.
The oval closet rod uses 1 mm wall thickness to keep the tube relatively light for handling and cutting while still providing a formed metal shell for typical hanging loads.
The KIT830-90-PC-SM corner closet rod has a polished chrome finish, which provides a smooth surface for hangers and coordinates with other polished chrome closet components.
The oval corner rod kit has two oval under-shelf flanges, two oval under-shelf center supports, a 90 degree corner oval closet rod, and fasteners for attaching the supports.
The Epco small oval corner rod kit 15mm W x 30mm H in polished chrome offers a defined 90 degree corner section with 11.5 inch sides, so a right-angle closet layout can carry hanging space around the corner on an oval profile. With two oval under-shelf flanges, two oval under-shelf center supports, and a 1 mm wall thickness oval rod, the KIT830-90-PC-SM is built for under-shelf mounting where a shelf-and-rod system needs a continuous corner transition.
Sold In: 1 Kit