Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Olympia hinge spacer gives you a simple way to fine-tune cabinet door overlay and clearance by a fixed 2 mm change, which helps dial in gaps on installations using compatible Olympia hinges. This spacer is identified as OLYMPIA 2MM SPACER W/2-HOLES, so you know it is built for 2 mm thickness adjustment in hinge layouts that use two screw bores at the plate. The part is supplied by Sugatsune America under manufacturer part number 360-DP2-P4, so it matches the Olympia hinge system details that installers recognize in that series. The spacer works within the hinge assembly as a controlled shim, so you can correct small layout shifts without changing the hinge or plate. That keeps door reveals consistent across runs where a 2 mm offset makes the difference between rub and smooth operation.
This Olympia 2mm hinge spacer is designed to sit in the hinge stack as a fixed-thickness element, so the 2 mm change is predictable every time it is used under a compatible mounting plate. When you apply it on an outset door, the spacer decreases overlay of that door by 2 mm, which shifts the door edge in relation to the cabinet front for cleaner alignment against neighboring doors or trim. On inset doors, the same 2 mm thickness increases clearance of the door inside the frame, which helps avoid edge contact when the door swings. Installers can double the spacer for 4 mm thickness where a single layer will not correct the layout, giving a second step of adjustment without altering hinge positions or drilling new holes.
This Olympia hinge spacer works in hinge assemblies that use Olympia series components, tying directly to hinge spacers and wedges within that hardware family. The web description identifies available mounting plates SL360-P4W-30T and SL360-P4W-32T, so the spacer serves in installations that specify those particular plates in the stack. On outset doors using these Olympia layouts, placing the spacer behind the mounting plate decreases overlay of the door by 2 mm, which addresses situations where doors are overhanging face frames more than planned. On inset doors, the same placement increases clearance of the door by 2 mm, giving extra working room between the door edge and the surrounding cabinet frame when clearances are too tight. In both applications, that predictable 2 mm change is especially useful across multi-door runs where the same hinge family and plates repeat.
The defined 2 mm thickness of the Olympia hinge spacer gives installers a known correction value, so each spacer delivers the same overlay or clearance change from cabinet to cabinet. When a layout only needs a small shift, the 2 mm change can bring an outset door overlay back into line or open an inset door gap enough to prevent rubbing on painted or laminated frames. If the misalignment is larger, the ability to double the spacer for 4 mm thickness provides a second step of control, using the same part rather than changing to a different hinge setup. The two-hole configuration keeps the spacer aligned with the mounting plate screws, so the hinge geometry set by plates SL360-P4W-30T or SL360-P4W-32T stays consistent after adjustment. Because the spacer functions within the hinge stack, you gain overlay and clearance corrections without shifting door drilling or cabinet boring patterns, which keeps rework time down on site or in the shop.
The Olympia hinge spacer changes the hinge stack by 2 mm, which decreases overlay on outset doors or increases clearance on inset doors wherever it is installed under compatible mounting plates.
The Olympia hinge spacer decreases overlay of outset doors by 2 mm, pulling the door edge back so it better aligns with adjacent doors or trim when the original overlay is excessive.
The Olympia hinge spacer increases clearance of inset doors by 2 mm, opening the gap between the door and the frame to reduce edge contact and allow smoother swing.
The Olympia 2mm hinge spacer can be doubled for 4 mm thickness, so two spacers together provide a larger change in overlay or clearance when a single 2 mm adjustment is insufficient.
The Olympia hinge spacer is referenced with mounting plates SL360-P4W-30T and SL360-P4W-32T, tying it to those specific Olympia hinge plate configurations in cabinet installations.
The Olympia hinge spacer with manufacturer part number 360-DP2-P4 is supplied by Sugatsune America, aligning it with the Olympia hinge hardware line used in many cabinet projects.
The Olympia hinge spacer 360-DP2-P4 gives you a defined 2 mm change in overlay or clearance, with the option to double to 4 mm when jobs require more correction. Using a spacer that is identified as OLYMPIA 2MM SPACER W/2-HOLES keeps your adjustments consistent wherever compatible Olympia plates such as SL360-P4W-30T or SL360-P4W-32T are installed. For cabinet work where small overlay shifts or extra inset clearance solve rubbing and misalignment, this hinge spacer provides a repeatable solution that fits directly into the Olympia hinge stack.