Hettich front fixing clip set is a left and right front fixing clip pair designed for attaching a drawer subfront to the slide system, so the front connection is positively located and repeatable. The set is specified for 13 mm, 16 mm, or 19 mm drawer subfront thickness, which means it works with common 1/2 inch, 5/8 inch, and 3/4 inch board stock used in many cabinet shops. The clips provide plus or minus 2 mm toolless height adjustment, letting you shift the drawer front up or down slightly to fine-tune reveals after mounting. A minimum drawer inside width of 165 mm, or 6 1/2 inches, is specified, so the application focuses on narrower drawers only where the clips can be positioned reliably along the front.
This Hettich America Corporation front fixing clip set is specified for use with drawer subfronts ranging from 13 mm to 19 mm thickness, so a shop working in 1/2 inch, 5/8 inch, or 3/4 inch material can follow the same interface layout. Each clip is mounted using two #6 x 3/4 inch flat head screws, creating a clear screw pattern that fits into standard shop drilling operations. The toolless plus or minus 2 mm height adjustment at the clip means the vertical position of the drawer front can be tuned after installation, instead of relying entirely on initial drilling accuracy. A minimum drawer inside width of 165 mm, or 6 1/2 inches, is specified, which defines where these clips fit into a cabinet program and how many narrower drawers will use alternative hardware.
The Hettich front fixing clip set is applied at the front connection point between a drawer subfront and its running system, so the drawer front is secured using a dedicated left and right clip pair. Because the set is specified for subfront thicknesses of 13 mm, 16 mm, and 19 mm, it serves projects built in 1/2 inch, 5/8 inch, or 3/4 inch panel stock, which covers many standard residential and commercial drawer programs. The minimum drawer inside width of 165 mm, or 6 1/2 inches, defines the lower size limit where this clip geometry fits, so layout designers can assign this part to drawers at or above that width and coordinate other solutions for smaller openings.
The Hettich 9140419 fixing clips provide plus or minus 2 mm toolless height adjustment, so installers can move the drawer front slightly up or down at the clip connection without loosening separate adjustment hardware, which streamlines fine-tuning of reveals across a cabinet run. Because the set uses two #6 x 3/4 inch flat head screws per clip, the mounting pattern is defined and repeatable, supporting consistent production drilling jigs and predictable performance in typical panel materials. The use across 13 mm, 16 mm, and 19 mm drawer subfront thickness allows one part number to serve different thickness programs, simplifying part stocking and reducing changeovers on the assembly line. With the drawer inside width minimum of 165 mm, or 6 1/2 inches, clearly stated, planners can lay out which drawer widths will use this front fixing clip set, helping organize hardware schedules by cabinet size.
The front fixing clip set is specified for 13 mm, 16 mm, and 19 mm drawer subfront thickness, covering 1/2 inch, 5/8 inch, and 3/4 inch materials commonly used in drawer construction.
The Hettich 9140419 front fixing clips provide plus or minus 2 mm toolless height adjustment, letting the drawer front be shifted slightly up or down to align cabinet reveals.
The front fixing clip set is specified for a minimum drawer inside width of 165 mm, or 6 1/2 inches, defining the smallest drawer interior where this hardware is intended.
The front fixing clips are installed using two #6 x 3/4 inch flat head screws per clip, establishing a clear and repeatable mounting pattern at the drawer front connection.
The set contains one front fixing clip for the left side and one for the right side, so a single set handles both sides of one drawer subfront.
This front fixing clip set is manufactured by Hettich America Corporation, aligning the part with the Hettich drawer hardware program.
The Hettich front fixing clip set with left and right clips, plus or minus 2 mm toolless height adjustment, and support for 13 mm, 16 mm, and 19 mm drawer subfront thickness gives shops a defined solution for adjustable drawer fronts. With a minimum drawer inside width of 165 mm, or 6 1/2 inches, and a two-screw mounting pattern using #6 x 3/4 inch flat head screws, the part fits neatly into engineered drawer programs where predictable layout and adjustment capabilities are important.
Sold In: 1 Set