TopLine Grant Double Profile, 7005 With Fascia 6'

TopLine Grant Double Profile 7005 Sliding Track Use

TopLine Grant double profile 7005 is a sliding door track that supports door movement in sliding door hardware assemblies. This track gives doors a defined running path, which helps doors move in a controlled line instead of wandering or binding. The track is part of the sliding door hardware category, so it is intended for applications where doors must slide rather than swing. The 6 ft length suits openings planned around that span, allowing installers to cover a run without splicing shorter sections. Because this product is identified as a double profile, it is designed to guide two door profiles in the same line of travel, which supports layouts using paired sliding doors. The track is produced by Hettich America Corporation under the TopLine Grant family, giving installers a clearly identified manufacturer part to match with project documents.

Sliding Door Track Details That Support Jobs

• The double I-beam track construction provides two internal running channels, which keeps each sliding door guided on a consistent path for smoother operation in a sliding assembly.
• The integrated fascia on the track forms a built-in facing element, which helps visually cover the working profile of the rail for a cleaner finished look around the sliding opening.
• The 6 ft track length sets a fixed working span, which helps installers plan door panel sizes and opening widths around a known dimension without cutting multiple shorter rails.
• Mounting holes approximately every 11 inches on center give repeated fastening points along the track, which supports more even load distribution into the supporting structure.
• Positioning of mounting holes at roughly 11 inch intervals helps simplify laying out fasteners, which can reduce layout time when transferring hole locations to a header or wall structure.

Mounting Hole Layout And Track Installation Use

The track design with mounting holes approximately every 11 inches on center gives a predictable fastening pattern for installation along a header or other support. Because the spacing repeats, installers can work steadily down the 6 ft length without individually marking each point from scratch. The double I-beam profile offers two internal paths for sliding components, and that geometry relies on accurate anchoring to keep the rail straight along its length. The fascia that is part of the track allows the visible face of the installation to align with surrounding finishes while the structural portion of the track remains behind it. With the track classified as builders hardware and sliding door hardware, it fits workflows centered on framing, casework, and door systems that require aligned, repeatable mounting.

Where This Double I-Beam Track Works Best

Sliding Door Hardware Track For 6 Foot Runs

This Hettich sliding door track belongs in sliding door hardware assemblies that are laid out around a 6 ft opening or panel run. The fixed 6 ft length allows the rail to span a typical opening without joints along the track, which benefits sliding action by presenting an uninterrupted running surface. Because the product is in the builders hardware class, it is suited to construction and woodworking projects where a defined structural header or support is available above the opening. The double I-beam track with fascia is used where two door profiles share the same upper track, so it suits paired door configurations that glide past each other. In these layouts, the clearly defined manufacturer part number 50549 helps align job submittals and field installation with the specified component. The fascia bonded to the track keeps the working steel profile visually covered along the run, which is useful when the track is in a visible room or casework face.

Track Features That Support Repeatable Alignment

The double I-beam track design provides parallel internal channels that guide sliding door hardware in a defined line, which promotes consistent door alignment along the entire 6 ft span. When the mounting holes are set approximately every 11 inches on center, each fastening point helps hold that geometry, limiting deflection between supports. This steady spacing gives installers a simple rhythm along the rail, which can streamline the process of anchoring into wood or other structural members. The fascia that is part of the track acts as a continuous face across the length, so once the rail is fastened, the visible line remains straight wherever the underlying mounting points fall. Identifying the track as TopLine Grant double profile 7005 ties it to a specific family of sliding components, which matters when matching door carriers and guides to the double-track geometry. The branding by Hettich America Corporation and the manufacturer part number 50549 give a stable reference, which supports repeat orders on multi-phase jobs that depend on using the same track profile. Together, these details allow installers to set out the track, align fasteners to the approximate 11 inch spacing, and achieve repeatable sliding performance across similar openings.

Common Questions About TopLine Grant 7005 Track

Select This Track For 6 Foot Sliding Runs

Choose the TopLine Grant 50549 double I-beam track with fascia when a 6 ft sliding door run is planned around a defined rail length and a clean finished face. The double profile design supports two sliding door profiles on one rail, while the mounting holes approximately every 11 inches on center provide a clear fastening pattern in the field. For projects drawing from Hettich America Corporation hardware, this sliding door hardware track ties directly into the TopLine Grant family for consistent, documented installations.