6' TopLine fascia is a 6 ft anodized aluminum trim piece designed for Grant SD, HD, and XHD sliding door systems, so it conceals the visible gap between the running profile and the door for a finished header appearance. The fascia spans the track area, hiding the mechanics from view, which keeps the installation visually consistent across multi-door runs. Because it is purpose-built as fascia for Grant SD, HD, and XHD systems, it matches the system geometry, supporting straightforward layout on projects that repeat the same hardware line. The 6 ft length gives generous coverage on common door openings, which helps reduce joints in the visible line over the doors. Anodized aluminum construction provides a stable, uniform surface along the full length, so the fascia maintains an even look around the sliding door hardware.
The fascia is designed for ceiling or wall installation, giving flexibility to mount it directly where the Grant SD, HD, or XHD running profile is fixed. This mounting choice supports different framing details, whether the track is carried on a header or fixed to a structural ceiling line. Straightforward installation with a simple clip-on action reduces handling time during trim-out, because the fascia snaps onto its clips rather than requiring separate alignment steps along the length. This clip-on design helps maintain a consistent reveal over the doors, as the clips hold the fascia in a repeatable position relative to the profile. Using an anodized aluminum fascia in this way provides a stable, straight edge along the opening, which supports a clean alignment between door tops and the visible header line.
This 6 ft anodized aluminum fascia sits above the door leaf in a Grant SD, HD, or XHD sliding door installation, covering the open space between the running profile and the top of the door. Because it is suitable for door thicknesses from 25 mm to 44 mm, it works across many typical interior sliding door builds that match these dimensions. In ceiling installations, the fascia lines up along the underside of the ceiling plane, so it visually bridges from the ceiling down to the moving door panel. In wall-mounted installations, it runs along the face of the wall over the track, concealing the structural header and track profile for a more uniform band over the opening. By intentionally concealing the gap between profile and door, this component allows the focus to remain on the door face instead of the hardware cavity. In multi-door or multi-bay layouts using Grant SD, HD, or XHD systems, repeating this 6 ft fascia segment helps create a continuous, coordinated line across adjacent openings.
The fascia uses a simple clip-on installation method, so it locates off its clips instead of relying on manual measuring at every point along the run, which supports straight, repeatable fascia alignment on the project. Because the fascia is anodized aluminum, it offers a uniform surface and color tone that stays consistent from one end of the 6 ft length to the other, helping joints between segments read as clean as possible when multiple lengths are used. The door thickness suitability from 25 mm to 44 mm ties the fascia position to a known relationship between track and door, which supports predictable reveals when detailing standard interior doors. Being specifically described as fascia for Grant SD, HD, and XHD sliding door hardware means it is built around the geometry of that sliding system family, which supports accurate fit at the track area. The note that fascia is not needed with a set of low profile fittings also guides product selection within the same hardware range, so the fascia is reserved for standard profile installations where the visible gap would otherwise remain open.
The 6' TopLine fascia is specified as a 6 ft component, so it spans typical single-door openings and helps minimize joints when finishing the header area over Grant SD, HD, or XHD sliding doors.
The fascia is designed for ceiling or wall installation and uses a simple clip-on method, so it attaches to its clips along the track line to cover the gap between profile and door.
The fascia is suitable for door thicknesses from 25 mm to 44 mm, which covers many interior sliding door constructions that coordinate with Grant SD, HD, or XHD hardware layouts.
The fascia is made from aluminium, anodised, providing a consistent metallic finish and a stable surface to align visually with other anodized sliding door components.
Fascia is not needed in combination with a set of low profile fittings, because those fittings already reduce the visible gap between the sliding door track profile and the door panel.
The fascia is described for Grant SD, HD, and XHD sliding door hardware systems, so it functions as the matching trim component over installations built around those running profiles.
This 6 ft anodized aluminum fascia from Hettich America Corporation is described specifically for Grant SD, HD, and XHD sliding door systems, so it is suited to projects using those profiles. Its role is concealing the gap between profile and door, which brings a finished header line to ceiling or wall-mounted track layouts. With suitability for door thicknesses from 25 mm to 44 mm and a clip-on installation method, it fits many interior sliding door builds while supporting efficient trim-out. For sliding door runs that use standard, non-low-profile fittings in the Grant SD, HD, or XHD family, this fascia provides the matching visible band that completes the hardware installation.
Sold In: 1 Each