8' TopLine Fascia for Grant SD/HD/XHD Sliding Door is an anodized aluminum fascia designed for the TopLine sliding door system, so it provides a dedicated trim solution matched to Grant SD, HD, and XHD sliding door profiles. The fascia is used for concealing the gap between profile and door, which covers the visible track area and creates a clean transition where the sliding hardware would otherwise remain exposed. Aluminium, anodised construction gives the fascia a durable surface finish, helping it resist wear at the edges where doors and trim meet during regular operation. The 8-foot length matches common run lengths on sliding installations, allowing long, continuous coverage across the door opening. As a Hettich America Corporation component in Sliding Door Hardware, it aligns with the rest of the TopLine system for consistent appearance along the full sliding assembly.
For ceiling or wall installation, this fascia adapts to how the Grant SD, HD, or XHD sliding track is positioned, so the same part can be used where the profile is framed into a header or fixed directly to structure. The straightforward installation: simply clip on design lets the fascia be attached after the track and doors are working, which helps sequence trim work after functional adjustments are complete. Because the fascia is designed for concealing the gap between profile and door, installers can align it precisely over the visible profile line and close that gap in a single step. Suitability for door thicknesses from 25 mm to 44 mm means the fascia face sits correctly relative to the door front across that range, maintaining a consistent reveal from project to project.
This TopLine sliding door fascia works with Grant SD, HD, and XHD sliding door configurations, giving a single trim component that serves across these related track families. By concealing the gap between profile and door, it occupies the space directly between the running profile and the moving panel, finishing the area that is otherwise left open. Ceiling or wall installation capability means it can be used along tracks fixed up into a header or mounted on the face of a wall, so the fascia follows the track position instead of dictating layout. Its suitability for door thicknesses from 25 mm to 44 mm lets it align with many interior sliding door constructions, covering slim and heavier doors within that dimension window under the same fascia profile.
The straightforward installation: simply clip on design turns the fascia into a finishing step that engages dedicated fascia clips, which simplifies alignment because the clips define the position relative to the sliding profile. Using aluminium, anodised material gives the fascia a rigid yet light structure that stays aligned on the clips while presenting a consistent anodized finish along the full 8-foot run. Because fascia length is 8', long openings can be trimmed with fewer joints, supporting a cleaner visual line over multi-panel Grant SD, HD, or XHD installations. The note that fascia is not needed in combination with a set of low profile fittings clarifies that this part is intended for standard profile configurations, so it is best applied where the visible gap between profile and door exists and needs to be concealed as part of the final appearance.
The 8' TopLine Fascia for Grant SD/HD/XHD Sliding Door conceals the gap between profile and door, so the exposed running profile area is covered for a cleaner finished appearance.
The fascia uses a straightforward installation: simply clip on method, so it attaches to fascia clips, turning final trim work into a quick clipping step.
The fascia is designed for ceiling or wall installation, allowing it to follow Grant SD, HD, or XHD tracks mounted up into a header or onto a wall surface.
The fascia is suitable for door thicknesses from 25 mm to 44 mm, so it aligns with many interior sliding door builds within that thickness range.
The fascia is made from aluminium, anodised, giving it a stable, finished surface that visually complements other anodized aluminum sliding components.
Fascia is not needed in combination with a set of low profile fittings, because those fittings remove the visible gap the fascia is designed to conceal.
This Grant SD, HD, and XHD sliding door fascia focuses on concealing the gap between profile and door, so it directly supports projects where exposed profiles would otherwise interrupt the finished look. Ceiling or wall installation capability lets it follow the track position across different framing approaches. With suitability for door thicknesses from 25 mm to 44 mm and a straightforward installation: simply clip on design, it fits into a practical workflow for trimming standard profile TopLine runs. For jobs built around these Grant sliding systems, this 8-foot anodized aluminum fascia offers a matched way to finish the visible profile area.
Sold In: 1 Each