Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
86 degree opening angle reduction clip gives S series hinges a fixed 86 degree stop, so the hinge will not swing past this point during use. This control matters when doors need to clear nearby walls or obstructions without overtravel. The reduction clip is designed for partial overlay S series hinges from 1/4 inch to 3/4 inch, so it supports a common range of cabinet door overlays in one solution. By matching that 1/4 inch to 3/4 inch overlay band, the clip helps installers handle many face-frame or frameless layouts using the same restriction style. The clip is classified as a hinge angle restriction clip, so it focuses on limiting motion rather than altering the hinge mount. Salice America branding identifies it for projects already using Salice S series hinges, simplifying product selection by tying directly to that hinge family.
The reduction clip for partial overlay S series hinges from 1/4 inch to 3/4 inch focuses on typical cabinet door overlays, so alignment work remains consistent across common door sizes. Because it limits the opening to 86 degrees, hinge motion is predictable when aligning doors near walls, appliances, or adjacent cabinets. That defined 86 degree stop helps plan reveals and clearances in the layout phase, reducing layout changes after doors are hung. As a hinge angle restriction clip, it works with the existing S series hinge geometry, so opening control is added while the base hinge alignment remains unchanged. This approach lets installers plan overlay and reveal using familiar S series behavior, simply capped at the 86 degree position.
This angle reduction clip is specified for partial overlay S series hinges from 1/4 inch to 3/4 inch, aligning it with many standard cabinet door overlays in shops and job sites. By targeting partial overlay, it supports applications where the door covers only part of the cabinet front, so the reduced 86 degree opening helps doors avoid contacting adjacent fronts or handles. The defined 1/4 inch to 3/4 inch overlay range means a single part can support small to moderate overlays, which is common in production cabinetry and custom runs using Salice America components. Limiting the opening to 86 degrees creates a consistent swing arc, which is useful when cabinets are installed close to side walls, tall panels, or appliances and clearance is tight. The clip functions within the S series hinge system, so it is used in projects already planned around that hinge style.
Setting the hinge to stop at 86 degrees gives every door using this reduction clip the same opening behavior, which supports repeatable layouts across a bank of cabinets. With the opening limited to 86 degrees, designers and installers can plan door swing relative to obstacles, knowing the arc will not exceed that angle in service. This predictable stop helps prevent door edges from striking nearby cabinetry or walls, supporting long-term appearance of finished surfaces. Because the clip is a hinge angle restriction clip, the limitation is applied directly to the hinge motion, so the stop point is built into the hinge action rather than relying on separate external stops. Using a clip identified by manufacturer part number SSP3377G ties the result to a specific Salice America component, which helps match hinge behavior across different locations that all specify the same part. This consistency is valuable for repeat work where the same door clearances are required in multiple projects.
The angle reduction clip is for S series hinges, so it restricts opening on that specific hinge family without changing their core mounting layout.
The reduction clip limits the opening to 86 degrees, so every door using it stops at the same controlled angle in day-to-day use.
The reduction clip is for partial overlay S series hinges from 1/4 inch to 3/4 inch, so it fits that overlay band on suitable cabinet doors.
The hinge angle restriction clip caps opening at 86 degrees, so doors swing less and avoid contact with nearby walls, cabinets, or appliances.
The clip is branded Salice America and described for S series hinges, so it aligns with cabinet projects using that manufacturer hinge line.
A partial overlay hinge angle limiter is useful when 1/4 inch to 3/4 inch overlay doors need a controlled 86 degree opening to protect surrounding surfaces.
The 86 degree opening angle reduction clip for partial overlay S series hinges from 1/4 inch to 3/4 inch gives projects a defined, repeatable door swing. By limiting the opening to 86 degrees, it supports layouts where door movement must clear nearby cabinetry or structures. As a hinge angle restriction clip identified by manufacturer part number SSP3377G from Salice America, it fits directly into S series hinge planning. For work centered on partial overlay with S series hinges, this clip provides a straightforward way to set consistent opening limits across the job.
Sold In: 2000 Each