
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Scale Miter Gauge SawStop TSA-SMG is a SawStop miter gauge designed to dial in accurate crosscuts and miters. The miter head features a pointer and 90 notches in 1 degree increments each side of 0 degrees, so angles can be set in consistent, repeatable steps on either side of square. A dedicated notch for 22.5 degrees on each side gives a direct setting for common frame and trim work. A Vernier scale lets you fine-tune any angle in 1/10 degree increments, supporting tight-fitting joinery when small deviations matter across multiple parts. An aluminum fence provides a large reference for workpieces, helping long or wide stock stay aligned to the blade path. A telescoping extension reaches up to 31 inches with the flip stop, so longer crosscuts can be laid out against a solid length reference.
The 18 inch long miter bar uses six adjustable washers to eliminate movement in the miter slot while ensuring a smooth glide forward and back, giving a stable feel as stock is advanced through the cut. As the bar rides in the slot with minimal play, the blade line stays predictable relative to the fence face, which helps reduce wandering cuts on narrow or small parts. The scale on top of the fence can be calibrated to enable precise crosscuts without having to measure and mark boards, turning the fence into a direct-reading length gauge for production-style workflows. By reading from the fence scale instead of separate markings on each board, cut lengths can be repeated at the same setting, supporting consistent part sizing across a run.
This SawStop Scale Miter Gauge is compatible with SawStop ICS, PCS, CNS, JSS, and CTS saws, so it integrates with a wide range of SawStop machines in both shop and jobsite environments. The aluminum fence provides a large reference for workpieces, helping users register cabinet parts, trim pieces, or project components firmly against a straight face during the cut. A telescoping extension that reaches up to 31 inches with the flip stop gives a longer support line, so wider panels or longer rails can be aligned to the blade without relying on temporary supports. The flip stop indexes on the fence in 1/32 inch increments, which supports fine length changes in small steps when dialing in a specific fit between mating parts. Use the flip stop to make repeated cuts at the same setting for identical project parts, so sets of rails, stiles, or stretchers can be produced at a consistent length.
The miter head pointer and 90 notches arranged in 1 degree increments each side of 0 degrees give discrete steps for angle selection, so users can move between common angles while preserving repeatability across different sessions. A Vernier scale that adjusts angles in 1/10 degree increments adds another layer of refinement when working on miters or compound assemblies where small angle errors multiply over several joints. The flip stop indexes on the fence in 1/32 inch increments, giving clear mechanical detents for length changes that matter on face frames, drawer parts, or trim runs. The flip stop's dual arms can be set independently at different lengths from the blade or linked together, allowing two reference points to be maintained when switching between dimensions on a project. All flip stop positions can be fine-tuned with a micro-adjuster, enabling controlled, small shifts rather than broad movements when matching an exact fit. A 1 year warranty supports ongoing use of the TSA-SMG miter gauge in regular cutting routines.
The SawStop TSA-SMG miter head features a pointer and 90 notches in 1 degree increments each side of 0 degrees, so users can set a wide range of miters on both sides of square.
The Vernier scale on the TSA-SMG lets angles be fine-tuned in 1/10 degree increments, supporting tighter joints when whole-degree settings are not precise enough.
The TSA-SMG uses an 18 inch long miter bar with six adjustable washers to eliminate movement in the miter slot while maintaining a smooth glide during cuts.
The TSA-SMG aluminum fence has a telescoping extension that reaches up to 31 inches, giving longer support for boards when crosscutting against the fence.
The scale on top of the TSA-SMG fence can be calibrated so crosscut lengths are set directly from the fence reading, reducing time spent measuring and marking each board.
The TSA-SMG Scale Miter Gauge is compatible with SawStop ICS, PCS, CNS, JSS, and CTS saws, so it works across those table saw platforms.
The SawStop Scale Miter Gauge TSA-SMG brings a notched miter head, Vernier scale, and calibrated fence scale together for controlled angle and length setups on SawStop table saws. An 18 inch miter bar with six adjustable washers supports a stable, smooth glide in the miter slot, helping maintain alignment as stock moves through the blade. The aluminum fence with telescoping extension up to 31 inches, paired with a flip stop that indexes in 1/32 inch increments and offers micro-adjustment, supports repeated cuts at consistent dimensions. With compatibility across SawStop ICS, PCS, CNS, JSS, and CTS saws and a 1 year warranty, this miter gauge is built for ongoing use on precise crosscut and miter work.
Sold In: 1 Each