Wall Anchors 3/8" Min Wall from Mechanical Plastics Corp are ALLIGATOR drywall anchors designed to hold high loads in solid walls, ceilings, and floors, giving installers a dependable fastening point in typical structural substrates. These ALLIGATOR anchors are also engineered to hold securely when they encounter an unexpected cavity, such as in hollow brick or hollow block, so a single anchor type can handle variable wall conditions on the same project. The anchors perform in drywall and tile over drywall as well, extending their usefulness across common interior finishes. A specially formulated polypropylene body flows into and locks up with any undercuts in the hole, helping the anchor adapt to minor drilling irregularities. This same polypropylene body bonds the screw to the wall and seals the hole to prevent moisture from entering, which supports long-term performance in standard interior environments.
These ALLIGATOR drywall anchors use a polypropylene body that flows into and locks up with any undercuts in the drilled hole, so normal drilling roughness can translate into additional mechanical keying. That flow characteristic means the anchor adapts to the shape of the hole in solid walls, ceilings, and floors, creating a customized fit for each fastening point. When the anchor encounters hollow brick, hollow block, or drywall, it still locks into available undercuts, so the installer retains holding power even across cavities. As the screw is driven, the polypropylene bonds the screw to the wall, turning the separate components into a single load-bearing assembly. At the same time, the material seals the hole to prevent moisture from entering, which helps protect the fastening point in typical interior conditions.
ALLIGATOR wall anchors are designed to hold high loads in solid walls, ceilings, and floors, so they serve in solid substrates where heavier-duty fastening is required. The same anchors also hold securely when they encounter an unexpected cavity in hollow brick or hollow block, allowing use across masonry units that have voids behind the face. Because they perform in drywall, they suit interior partitions where a cavity exists behind the board. Their performance in tile over drywall means they address situations where a hard tile surface covers a drywall backing, such as tiled walls in standard interior rooms. Across these conditions, the polypropylene body flows into and locks up with any undercuts in the drilled hole, forming a mechanical interlock tailored to the specific base material.
The specially formulated polypropylene body in these ALLIGATOR anchors flows into and locks up with undercuts in the hole, turning small surface irregularities into grip points that increase resistance to pullout. As the screw is driven, this same polypropylene bonds the screw to the wall, so the screw and anchor act together as a unified fastening system instead of separate components. That bonding behavior helps stabilize attached fixtures because the load is shared along the full length of the engaged material. By sealing the hole to prevent moisture from entering, the polypropylene also helps protect the immediate bore area from moisture ingress, which supports the integrity of the substrate around the fastener. In ceilings, floors, solid walls, hollow brick, hollow block, drywall, and tile over drywall, these combined effects translate the anchor design into consistent field performance.
The 13101 model is an ALLIGATOR wall anchor classified as a drywall anchor, so it is intended for use where drywall is part of the wall assembly.
These ALLIGATOR anchors are designed to hold in solid walls, ceilings, and floors and also hold securely in hollow brick, hollow block, drywall, and tile over drywall.
The specially formulated polypropylene body flows into and locks up with undercuts in the hole, increasing mechanical interlock and helping the anchor resist pullout under load.
By bonding the screw to the wall, the polypropylene body creates a unified anchor-and-screw system, which helps stabilize mounted items during everyday use.
Sealing the hole to prevent moisture from entering helps protect the immediate fastener area, supporting the surrounding substrate and finish over time.
When these anchors encounter an unexpected cavity in hollow brick, hollow block, or drywall, the design still holds securely by locking into available undercuts.
Choosing ALLIGATOR Wall Anchors 3/8" Min Wall from Mechanical Plastics Corp provides a single anchor style that is designed to hold high loads in solid walls, ceilings, and floors while still holding securely in hollow brick, hollow block, drywall, and tile over drywall. The specially formulated polypropylene body flows into and locks up with undercuts in the hole, bonds the screw to the wall, and seals the hole to prevent moisture from entering, turning each drilled hole into a tailored, moisture-resistant fastening point ready for demanding interior applications.
Sold In: 1 Box