American Veneer Ash edgebanding preglued 13/16 ties exposed panel edges into ash surfaces so cabinet sides, shelves, and door edges present a consistent wood look around the entire piece. This Cedan Inc edge banding uses American Veneer Ash to match ash-based projects, supporting a unified appearance on visible edges of plywood, particleboard, or similar substrates. The 13/16 inch width gives coverage beyond a typical 3/4 inch panel thickness, allowing a small trimming margin so installers can flush the edge after bonding. As a preglued product, the edgeband arrives with adhesive already applied to the back, so installers can activate the glue rather than rolling on separate adhesive, which streamlines repetitive runs on cabinetry or fixtures. The defined product identity as ash edge banding helps shops keep part AEASH1316PG clearly separated from other wood species during production.
The 13/16 inch width on this American Veneer Ash Edgebanding Preglued 13/16 Width is sized to overlap a typical edge, which supports accurate trimming with hand tools or edgebanding equipment after the bond is activated. Because the Cedan Inc strip is preglued, the adhesive layer is already calibrated to the band thickness, so installers can work with consistent glue coverage across each length rather than adjusting separate glue spread for different runs. The ash veneer face presents a uniform surface that responds predictably to trimming and light sanding along the edge line, helping maintain a straight, clean transition between band and panel. Using a dedicated ash strip like this keeps the installation parameters for AEASH1316PG consistent from job to job.
This American Veneer Ash edgebanding preglued 13/16 is suited to exposed edges on ash-toned cabinetry, casework, and shelving where the visible side of a panel transitions to the edge. The ash veneer surface allows the edge treatment to visually follow ash doors, drawer fronts, or face frames, helping projects that rely on ash color and grain maintain continuity around corners. Its 13/16 inch format works with many sheet-good thicknesses common in woodworking, and the preglued construction aligns well with workflows that rely on heat-based activation for linear edges. In shops that standardize on ash finishes, stocking AEASH1316PG gives a clear match point for edge treatment wherever ash surfaces appear.
The combination of American Veneer Ash material and pre-applied adhesive helps installers treat this product as a repeatable component rather than a custom edge solution on each build. By keeping the width fixed at 13/16 inch, Cedan Inc provides a band that responds the same way under trimming knives or routers across multiple jobs, which reduces adjustment between panels. The preglued format sets a known adhesive thickness along the back, so activation techniques developed for AEASH1316PG apply across future runs, supporting consistent bond lines without recalculating glue volume. Identifying this strip as edge banding within the edgebanding and surfacing category allows production planners to assign it directly to edging stages, limiting handling steps. Across cabinetry or fixture programs that repeat ash finishes, these details support stable appearance and predictable workflow timing for every edge run.
The product uses American Veneer Ash, so the edge presents an ash wood surface that visually follows other ash components in cabinets or casework.
The ash edgebanding has a 13/16 inch width, giving coverage beyond common panel thicknesses and leaving material to trim back to a flush, clean edge.
This Cedan Inc edgebanding is preglued, so adhesive is factory-applied on the back and installers activate that glue instead of spreading separate adhesive.
The edge banding is used on exposed panel edges in cabinets, shelving, and casework, so ash surfaces carry cleanly from faces to edges.
The AEASH1316PG identifier uniquely tags this 13/16 inch preglued American Veneer Ash edgeband for ordering, storage, and production staging.
The strip is in the edge banding product class within edgebanding and surfacing, marking it as a dedicated solution for finishing panel edges.
The American Veneer Ash edgebanding preglued 13/16 brings together ash veneer, a 13/16 inch width, and factory-applied adhesive to handle exposed edges on ash projects with one defined strip. Cedan Inc assigns the AEASH1316PG part number so shops can specify this exact ash edge banding whenever panel cores need an ash-finished perimeter. For woodworking operations aiming to match edges to ash faces while keeping a predictable edgebanding step, this product aligns the material, width, and glue format into a single straightforward choice.
Sold In: 1 Roll