PVC Tieera Linea edgebanding defines a specific PVC edge banding strip that finishes exposed panel edges on casework and components. The .018 inch thickness creates a slim edge detail that covers raw substrate while keeping profiles tight for modern cabinet lines. The 15/16 inch width spans typical panel thickness with a little tolerance, so the installer can trim flush after bonding for a straight finished edge. The 600 FT length on a single roll supports long production runs without frequent changeover, which helps maintain consistency from cabinet to cabinet. The PVC material provides a uniform surface along the edge, so the finished run looks continuous across doors, drawer fronts, and carcass edges. Branded as Rehau, Inc., this edge banding aligns with professional shop expectations for named product lines when matching existing work or standardizing materials in the shop.
This PVC Tieera Linea edge banding is defined at 15/16 inch width, which allows it to span the face and back of typical panel edges before trimming, supporting flush-trim workflows on common casework. The .018 inch thickness specifies a thin band that responds well to established edge-banding equipment settings geared for light PVC strips. With 600 FT on the roll, a shop can set up an edgebander or handheld system once and run a series of doors, shelves, or carcass edges without material interruption, which supports repeatable fit and appearance across a project. Defined as PVC edge banding from Rehau, Inc., the product slots into standard edge-banding processes using PVC-rated adhesives and trimming tools.
This product is categorized as PVC edgebanding and edge banding, so it serves to finish exposed edges on panels in cabinets, furniture, and other woodworking assemblies that use sheet goods. The 15/16 inch width provides coverage across the edge and a slight overhang, which suits applications where panels fall near the three-quarter inch range and require a small margin for flush trimming. Because the banding is .018 inch thick, it suits projects where a light edge presence is preferred rather than a heavy bullnose, such as frameless cabinetry and flat-panel components. The 600 FT roll length supports shop environments that run repeated cabinet parts or commercial millwork, allowing long sequences of panels to be edged from the same roll so the visual result stays consistent from part to part.
The defined .018 inch thickness influences how the edge banding behaves under trimming knives and routers, providing a predictable amount of material to shave without leaving a pronounced lip, which supports clean alignment between edge and face. The 15/16 inch width establishes working room on both faces of the panel edge, so fabricators can align the strip quickly and rely on the trimming cycle to finalize the edge instead of chasing exact positioning by hand. A 600 FT roll reduces handling during production, which helps maintain consistent feed tension and temperature exposure on edgebanders for more uniform adhesion along cabinet runs. The Rehau, Inc. branding and Tieera Linea designation clearly identify the line and manufacturer part number 302164-054, which matters when matching prior installations or documenting materials by part number in project records. Defined within the edgebanding and surfacing category, this strip integrates into workflows focused on finishing sheet-good edges to match the faces used elsewhere on the job.
The product is defined as 15/16 inch width and .018 inch thickness, providing coverage over common panel edges with a slim profile that trims flush for a clean finished line.
The 600 FT length supplies material for extended runs of doors, shelves, or cases, so shops can edge multiple components from one roll and maintain consistent appearance across a project.
This product is specified as PVC edgebanding, so it fits workflows that are already set up for PVC edge materials in terms of bonding and trimming practices.
The edge banding is branded Rehau, Inc., giving shops a clearly identified manufacturer when they need to match existing Rehau PVC edges or record material sources.
The .018 inch thickness establishes a light edge that trims back smoothly, helping the edge sit nearly flush with the panel face without creating a bulky transition.
As PVC edge banding in 15/16 inch width, this strip works well on panel-based cabinets and furniture where exposed edges need coverage and a slim, modern profile.
This PVC Tieera Linea edgebanding from Rehau, Inc. combines .018 inch thickness, 15/16 inch width, and a 600 FT roll to support continuous edge finishing on panel-based projects. When those dimensions and material align with your cabinet or furniture run, this defined 302164-054 edge banding provides a consistent way to cover raw edges and keep visual lines uniform from part to part.
Sold In: 1 Roll