Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 8400 drawer slides in the 6 inch length give you a compact, full extension option when drawer depth is limited, so short utility drawers can still open fully for clear access to contents along the entire slide travel.
This 8400B 6 model is a side mount, ball bearing drawer slide, so the slide carries on the cabinet sides and runs on ball bearings, which supports smooth motion and consistent feel on small drawers used repeatedly in cabinets or shop fixtures.
The slide uses an anochrome finish, so the steel surface is treated for a uniform metallic appearance, which helps the hardware blend into typical cabinet interiors where a bright but neutral finish is preferred.
The product is identified as non-handed, so the same member design works on either side of the cabinet and drawer, which simplifies layout and reduces orientation errors when installing multiple identical drawers.
This slide belongs to the KV 8400 series and uses a 32 mm pattern, so the mounting holes line up with 32 mm system boring, which speeds installation in cabinets built around that standard drilling layout.
This KV Model #8400 in the 6 inch length is a side mount slide with 1/2 inch plus 1/32 inch minus 0 inch side clearance on each side, so planning the drawer width around that clearance creates the running gap needed for the ball bearings to operate smoothly.
The 1-13/16 inch overall slide height defines how much vertical space the runners occupy on the drawer sides, so the cabinet design can allot enough side height while still leaving edge room for the drawer bottom, applied fronts, or other hardware.
The 32 mm pattern indicated in the description means the mounting holes align to a 32 mm system drilling grid, so cabinets built on that standard can position these slides using existing line bores without separate layout steps.
The recommended fasteners are #7 x 1/2 inch Phillips truss head, so using that size and head style matches the slide hole design, which helps seat the slide firmly against the cabinet and drawer members without pulling through the mounting pattern.
This 6 inch ball bearing drawer slide works where the cabinet or enclosure depth is short, because the 6 inch length supports shallow drawers that still need full extension travel within a compact footprint.
The side mount configuration places the hardware along both drawer sides, so it suits cabinets built with side panels wide enough to accept 1-13/16 inch tall runners plus the specified side clearance, such as utility cupboards or fixture drawers.
The non-handed construction lets one slide design serve either left or right positions, so installers can stock a single model for both sides of the drawer, which streamlines organizing hardware on larger cabinet runs.
The 32 mm pattern supports cabinets drilled on that system, so European-style casework with line boring can position these slides directly into existing holes, which supports repeatable slide placement across a bank of small drawers.
Because this product is part of the 8400 series with full extension, short drawers achieve full travel, which helps when the cabinet is used for small parts, tools, or supplies that would otherwise sit deep in a limited depth opening.
The defined side clearance of 1/2 inch plus 1/32 inch minus 0 inch each side gives an exact drawer width target, so builders can standardize box dimensions and expect similar slide performance from one drawer bank to the next.
The specified 1-13/16 inch slide height sets a clear constraint for the drawer side height, so fabricators can size sides to accommodate the runner while keeping enough material above and below for joinery or applied edges.
The lever disconnect feature allows the cabinet and drawer members to separate, so during fabrication and finishing, the drawer box can be worked independently and later reinstalled on the same mounting points.
The ball retainer latch keeps the bearings captured, so the running elements stay aligned within the slide channels, which supports smooth action after repeated removal and reinstallation using the lever disconnect.
The anochrome finish on the slide surfaces provides a consistent metallic coating, so when drawers are open, the hardware presents a uniform look that aligns with many commercial and shop cabinet interiors.
The KV Model #8400 series designation and manufacturer part number 8400B 6 give a precise reference, so shops can reorder the same slide for future builds or repairs and match slide length, mounting pattern, and functional details.
The 8400B 6 is a Knape and Vogt side mount, ball bearing drawer slide with full extension, so it carries on the cabinet sides and lets shallow drawers open fully on bearings.
The KV 8400B 6 slide length is 6 inches, so it suits cabinets and drawers where depth is limited but full extension drawer travel is still required.
The 8400B 6 drawer slide uses 1/2 inch plus 1/32 inch minus 0 inch side clearance on each side, so the drawer width is set to maintain a smooth running gap.
The KV 8400B 6 slide height is 1-13/16 inch, so cabinet and drawer side designs can allocate that vertical space for the runner on each side.
The recommended fasteners for the 8400B 6 slide are #7 x 1/2 inch Phillips truss head screws, so the screw size and head style match the slide mounting pattern.
The KV 8400B 6 drawer slide uses a 32 mm pattern, so its mounting holes align with 32 mm system drilling used in many European-style cabinets.
The Knape and Vogt 8400B 6 full extension, side mount ball bearing drawer slide combines a 6 inch length, defined side clearance, and 1-13/16 inch height, so it fits compact drawers that still need full access and repeatable mounting in 32 mm system cabinets.