Formwood Almond Melamine Edgebanding gives a finished almond edge to melamine or similar sheet goods, so raw substrate edges are covered and projects present a consistent color. The edgebanding is identified as a polyester edge banding, which means the material is designed to act as a durable facing on exposed edges. The 13/16 inch width works with common 3/4 inch panels, giving a bit of overhang for trimming and flush detailing. The roll length of 250 feet supports longer runs or multiple cabinets from a single roll, which reduces roll changes during production. The product is pre-glued, so the adhesive is already on the back of the tape and activates in one pass during application. The almond color ties into Formwood almond melamine layouts, so door and panel edges visually match the face material.
This Formwood almond melamine edgebanding uses a pre-glued backing, so adhesive is already applied to the rear of the tape for straightforward application in the shop. The 13/16 inch width is sized to sit slightly proud on a 3/4 inch edge, so the band can be trimmed flush for a clean line after bonding. With 250 feet on a roll, a run of cabinet parts, shelves, or panels can be processed continuously, which supports repeatable application settings. The almond melamine face is produced by Formwood as an edge banding, so the edge surface is made to visually coordinate with almond-toned melamine panels from the same color family.
Formwood Almond Melamine Edgebanding is a polyester edge banding intended for use on panel edges where an almond melamine look is required, so cabinet carcasses and shelving built from melamine panels gain a finished appearance. The 13/16 inch width is sized for edges based on 3/4 inch material, so face-frame-less cabinet sides, top and bottom panels, and shelves can be banded using the same roll. Because the roll length is 250 feet, runs of multiple cabinets or closet sections can be processed without stopping to change material, which fits shop environments working on repeated almond melamine projects. The almond color on the melamine face ties edges into almond-colored faces, so door edges, exposed cabinet sides, and shelf fronts read as part of a continuous almond scheme.
This polyester edge banding from Formwood presents a melamine almond surface, so the tape is built to give a uniform color band along the perimeter of panels. The pre-glued design carries adhesive factory-applied to the back of the tape, so application becomes a single pass of heat and pressure, which supports repeatable workflow from piece to piece. The 13/16 inch sizing gives a predictable amount of overhang on 3/4 inch stock, so trimming equipment can be set for a consistent cut pattern across many parts. With 250 feet available, application settings can remain unchanged through long runs, which supports consistent edge quality from the first component to the last in an almond melamine job. The product identification PGALM13/16 marks the almond color and 13/16 inch width, so future reorders of the same edgebanding maintain color and size continuity on follow-up work.
Formwood Almond Melamine Edgebanding is described as polyester edge banding, which provides a formed facing on panel edges for an almond melamine look.
Formwood Almond Melamine Edgebanding is 13/16 inch wide, which covers edges cut from 3/4 inch sheet material with extra width for final trimming.
The Formwood almond melamine edgebanding roll length is 250 feet, which supports edging multiple cabinets or shelving sections in a single run.
This Formwood almond melamine edgebanding has adhesive already applied to the back, so heat and pressure activate the glue during edge application.
The 13/16 inch Formwood Almond Melamine Edgebanding fits typical 3/4 inch panel edges, leaving slight overhang to trim flush after bonding.
The product is identified as Formwood Almond Melamine Edgebanding, which means the edge surface presents an almond-toned melamine appearance.
Formwood Almond Melamine Edgebanding 13/16 inch W x 250 feet pre-glued offers a polyester edge banding solution when an almond melamine appearance is required on exposed panel edges. The 13/16 inch width, 250 foot roll length, and pre-glued backing support straightforward processing of 3/4 inch melamine components in almond layouts. Selecting this PGALM13/16 Formwood edgebanding keeps color, width, and material type aligned across current and repeat almond jobs that use melamine-faced sheet goods.
Sold In: 1 Roll