
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
1-1/16 inch closet rod flange describes this Knape and Vogt long closet rod flange that is designed for 1-1/16 inch diameter tubing, so it supports standard round closet rods used in many closet layouts. The chrome finish on the flange provides a clean metal surface that matches chrome closet tubing, which helps maintain a consistent look across an installation. This flange has a 1-1/16 inch diameter design that captures the rod end, so the tubing seats securely instead of floating against the panel. The product is identified as manufacturer part 632 CHR, which lets installers match it with existing Knape and Vogt layouts that call out this number. The SAP description lists a 5mm peg, tying this flange to systems that use 5mm support pins in closet side panels.
The 5mm peg on this Knape and Vogt closet rod flange works with 5mm bore holes, so it aligns with common system holes in closet side panels. Two pins spaced 1-1/4 inches on center use 3/16 inch bore holes, so the flange uses a pair of small-diameter holes to resist twisting while the rod is loaded. The flange also has one hole for screw mount, so it can be fixed firmly to the panel and better handle downward forces from hanging clothes. Because the flange is built for 1-1/16 inch diameter tubing, installers can coordinate drilling, peg placement, and rod cutting around a known rod size.
This Knape and Vogt long closet rod flange fits into 5mm bore systems, so it is suited to closets that already use 5mm line-boring for shelves and hardware. The two pins at 1-1/4 inches on center for 3/16 inch bore holes anchor the flange in the side panel, so it holds the closet rod securely at each end of a run. Because the flange is sized for 1-1/16 inch diameter tubing, it pairs with closet rods cut from that tubing size in wardrobe, reach-in, or utility closet applications. The chrome finish allows it to blend with chrome closet tubing, so it can be used where hardware is visible and needs a consistent appearance. The SAP description listing a 5mm peg confirms it is built around the 5mm pin approach that is common in modular closet systems.
The 5mm peg on the 632 CHR flange sets the vertical and horizontal position of the rod end from the side panel, so repeated drilling patterns can produce uniform rod height across multiple closet sections. The two pins on 1-1/4 inch centers engaging 3/16 inch bore holes spread the load into the panel, so the flange resists rotation when hangers are pulled or clothes are shifted. The single hole for screw mount ties the flange back to the panel with a mechanical fastener, so the rod support stays seated over time instead of creeping out of the bore holes. Matching the flange to 1-1/16 inch diameter tubing controls the fit between rod and support, so installers can cut and install rods knowing the ends will seat consistently without excessive clearance. The chrome finish on the flange lets it visually align with chrome tubing, so closet interiors can maintain an even metallic look from panel to panel.
The 632 CHR long closet rod flange is designed for 1-1/16 inch diameter tubing, so it supports standard 1-1/16 inch round closet rods along the length of a closet.
The closet rod flange uses a 5mm peg that fits a 5mm bore hole, so it locates in system holes commonly drilled in closet side panels.
The flange has two pins 1-1/4 inches on center for 3/16 inch bore holes, so it locks into the panel and resists rotation under load.
This closet rod flange has one hole for screw mount, so it can be fastened to the panel to better handle downward forces from hanging clothes.
The flange has a chrome finish, so it visually matches chrome closet tubing and supports a consistent metallic look in the closet interior.
Manufacturer part 632 CHR identifies this specific Knape and Vogt long closet rod flange, so it can be matched to layouts and reorder lists using that number.
This Knape and Vogt 1-1/16 inch closet rod flange pairs a 5mm peg, two pins on 1-1/4 inch centers for 3/16 inch bore holes, and a screw mount hole to stabilize the rod end, so it supports consistent installations around 1-1/16 inch chrome tubing.
Sold In: 1 Each