Cork Bumpers 3/8 Diameter For Doors And Drawers

Cork Bumpers 3/8 Diameter describe cork pads sized for precise point contact on doors, drawers, and work surfaces, so impact is focused and controlled rather than spread across a larger area. The 3/4 thickness creates a substantial cork layer between surfaces, which helps absorb contact when doors or drawers close against cabinets, cases, or tables. As a cork pad, this part fits the door and drawer bumpers category, giving installers a defined solution when a project calls for compressible contact points. The Boston Felt brand identifies a dedicated manufacturer of cork and felt products, so this part number FDCP5 ties directly to cork bumper use instead of being a generic pad.

Practical Details That Matter On Every Install

• The 3/8 diameter focuses the contact point, which helps doors and drawers land on a consistent spot, supporting repeatable alignment from piece to piece across a run.
• The 3/4 thickness provides a tall cork cushion, which gives fabricators more material depth to work with when setting how far doors or panels stand off from the case.
• The pressure sensitive adhesive backing is designed to bond the pad by pressing it into place, which streamlines installation on cabinet, work surface, or table projects.
• Being categorized as door and drawer bumpers defines this cork pad for impact and contact control, which helps hardware planners assign it where a soft stop is needed.
• Rolls of 1,000 or 5,000 support full roll quantities only, which suits shop environments that standardize on one bumper size and use it across multiple jobs.

Installation And Adhesive Backing Workflows

The pressure sensitive adhesive backing turns this FDCP5 cork pad into a peel-and-press solution, so positioning on doors, drawer fronts, or frames can be handled in a single motion. As a cork bumper designed for work surfaces and tables, it adheres to flat substrates, supporting clean bonding on prepared cabinet parts, fixtures, or bench surfaces. The 3/8 diameter fits tight spots on smaller fronts or frames, so installers can place bumpers exactly where the door or drawer contacts the cabinet. With a 3/4 thickness cork body, the pad compresses under load while still preserving its stand-off height, which helps maintain a consistent gap where parts meet.

Using FDCP5 Cork Pads In Daily Shop Work

Where These Cork Bumpers Fit Best

This cork pad sits in the Work Surface & Tables and Bumpers category, so it is positioned for flat-panel, bench, and cabinet work where contact points matter. As a door and drawer bumper, it is suited to projects that need a cork interface wherever a moving part lands against a fixed surface. The 3/8 diameter helps these bumpers fit on narrow rails or tight face-frame sections, which is useful on smaller casework or closely spaced fronts. With 3/4 thickness, the cork body can handle deeper reveals, so fabricators can apply the same pad on thicker doors or fronts and still achieve a functional stop. The FDCP5 part number from Boston Felt lets shops specify this exact configuration when repeating details across multiple jobs.

Why Dimensions And Adhesive Improve Results

The combination of 3/8 diameter and 3/4 thickness gives installers a predictable bumper profile, which simplifies laying out stop locations and matching door reveals from cabinet to cabinet. Because this product uses pressure sensitive adhesive backing, installers can position bumpers at the end of assembly or during fitting without additional fasteners or separate bonding steps. The adhesive-backed cork pad design lets fabricators adjust placement along rails and stiles during mock-up, then press into final position once the closing action feels right. Sold in full roll quantities only, in rolls of 1,000 or 5,000, this configuration supports production workflows where a shop stocks one Boston Felt cork bumper and deploys it consistently across work surfaces, tables, doors, and drawers.

Common Questions About FDCP5 Cork Bumpers

Select FDCP5 Cork Pads For Consistent Contact Points

The FDCP5 Cork Bumpers 3/8 Diameter, 3/4 Thickness from Boston Felt combine defined dimensions with a pressure sensitive adhesive backing, giving shops a repeatable solution for doors, drawers, and work surfaces. As a cork pad classified under door and drawer bumpers in the Work Surface & Tables group, it fills the role of a dedicated contact point rather than a general-purpose material scrap. With rolls of 1,000 or 5,000 sold in full roll quantities only, this configuration aligns well with cabinet and woodworking environments that rely on consistent parts from Wurth Baer Supply to support ongoing production.