1-3/4" steel interlocking panel clip provides a low-profile way to fasten wall-panels, wall-hung cabinets, mirrors, bed headboards, and displays, so panels sit close to the wall for a cleaner finished look on built work. The clip uses two interchangeable interlocking pieces that mate perfectly, creating a secure fastening that keeps mated surfaces aligned in use. This interlocking action holds the mounted part to the substrate while still allowing straightforward lift-off when disassembly is required. The assembled system has only 1/8" thickness, which keeps the gap between the mounted component and the wall minimal for tight visual tolerances. The panel clip is made from .062" gauge steel, giving a solid metal interface wherever panel assembly fittings are needed. A zinc plated finish on the steel adds a protective layer that helps the clip stand up in typical woodworking and shop environments. The design belongs to the panel assembly hardware class, so it fits naturally into fastener-based build workflows for casework and display work.
The flushmount, single panel clip design creates a fastening system where the two interlocking pieces mate at only 1/8" assembled thickness, so fit-up against the wall remains tight and consistent. Because the pieces are interchangeable, installers can position either side on the wall or on the mounted component, which simplifies layout on panels, cabinets, mirrors, headboards, and displays. The four countersunk holes sized for #6 flat head screws give a defined screw pattern, helping keep the clip square during installation and ensuring that screw heads sit below the working surface for full engagement. The .062" gauge steel and zinc plated finish provide a stable, metal-to-metal bearing surface at each connection point, supporting accurate fit when multiple clips are aligned across a large panel assembly.
This interlocking panel clip from Selby Furniture Hardware is specified for wall-panels, wall-hung cabinets, mirrors, bed headboards, and displays, so it fits into a wide range of interior woodworking and fixture projects. In wall-panel installations, the 1/8" assembled thickness keeps decorative panels close to the substrate, which helps maintain consistent reveals along edges and corners. For wall-hung cabinets, the .062" gauge steel creates a metal connection between the cabinet case and the wall, aiding in stable support across multiple clips. When used with mirrors, the flushmount design minimizes the visible offset from the wall surface, supporting a more integrated look in bath or dressing areas. On bed headboards and display components, the two-piece, mating design lets the component engage with the wall-mounted half in a repeatable way, supporting straightforward removal and re-hanging when layouts change.
The K418Z flushmount, single panel clip uses two interchangeable interlocking pieces that mate perfectly, so the connection between wall and mounted part centers on a defined metal interface rather than relying on bearing against the wall surface. That interlock controls position in plane, which helps maintain alignment when several clips are installed along a wide panel or cabinet run. The 1/8" assembled thickness establishes a known stand-off dimension, aiding in predictable fit when coordinating trim, adjacent panels, or scribed parts. Because all four screw holes are countersunk for #6 flat head screws, the screw heads sit within the clip body, preserving full contact between mating faces for secure fastening. The .062" gauge steel and zinc plated finish together support a robust connection in indoor woodworking environments, so the clip continues to hold panels, cabinets, mirrors, headboards, and displays at the intended angle and spacing through repeated use.
The 1-3/4" steel interlocking panel clip is specified for wall-panels, wall-hung cabinets, mirrors, bed headboards, and displays, so it serves a range of interior woodworking and fixture installations.
The 1/8" assembled thickness keeps the mounted panel or cabinet close to the wall surface, helping maintain tight reveals and a flush appearance across adjacent components.
The K418Z panel clip is made from .062" gauge steel with a zinc plated finish, providing a solid metal interface with added surface protection in typical indoor woodworking environments.
The panel clip uses two interchangeable interlocking pieces that mate perfectly, creating a secure fastening that holds the mounted part to the wall while maintaining alignment.
The four countersunk holes on the clip are designed for #6 flat head screws, so the screw heads sit flush within the clip and allow the interlocking faces to engage fully.
As a panel assembly fitting in the panel assembly hardware class, the interlocking clip provides a repeatable fastening method that fits naturally into fastener-based panel and casework builds.
The 1-3/4" steel interlocking panel clip from Selby Furniture Hardware combines two interchangeable, perfectly mating pieces, .062" gauge steel, zinc plating, and 1/8" assembled thickness to support clean, flush installations of wall-panels, wall-hung cabinets, mirrors, bed headboards, and displays. The four countersunk holes sized for #6 flat head screws define a consistent mounting pattern that supports square, repeatable installation across projects. For panel assembly hardware needs where a low-profile, metal-to-metal connection is required, this flushmount, single panel clip provides a focused solution matched to interior woodworking and display work.
Sold In: 500 Set