Corner Braces Plastic Glue Boxes Tabs Extended Up, Translucent - 100 Each

Corner Brace Tabs Extend Up Translucent For Cabinets

corner brace tabs extend up translucent identifies this Hughes Supply corner brace as a plastic glue block designed for cabinet corners. The brace belongs to the Corner Braces and Glue Blocks product class, so it works as a structural support in cabinet construction where solid corner reinforcement is needed. It is made of high impact, specially compounded plastic material, which resists cracking during normal cabinet assembly so installers can work quickly without babying the part. The translucent color helps the brace sit unobtrusively inside light cabinet interiors, which matters on open boxes and glass-front runs. Braces are 3-5/8 inches long and 3/4 inch deep, giving a compact footprint that fits typical cabinet corner spaces while still providing useful bearing surface for joints. The product is sold in full box quantities only, supporting batch work where consistent parts across a job reduce layout variation.

Key Corner Brace Details That Save Time

• Made of high impact, specially compounded plastic material, this corner brace handles normal stapling and fastening loads without shattering, which supports straightforward production work in cabinet shops.
• The plastic material can be stapled through without shattering, allowing installers to drive staples directly through the brace into cabinet members and keep joints tight without pre-drilling.
• The brace will also accept glue, so builders can use adhesive along with mechanical fasteners to create a reinforced corner that supports long-term cabinet box stability in service.
• Off-center screw holes provide easier screw gun access into the corner of the cabinet, giving installers a better angle for driving fasteners where space is restricted near the back and sides.
• Braces are 3-5/8 inches long and 3/4 inch deep, offering enough surface to support the joint while still fitting into tight cabinet corners without interfering with other internal components.

Installation And Fastening Use In Cabinet Corners

This plastic corner brace can be stapled through without shattering, so during assembly installers can pin it directly to cabinet sides and bottoms in a single pass. Because the brace will also accept glue, adhesive can be applied along the contact faces before fastening to create a bonded and mechanically locked corner. Off-center screw holes are designed to provide easier screw gun access into the corner of the cabinet, helping the driver bit enter fasteners at a workable angle even in narrow boxes. The 3-5/8 inch length and 3/4 inch depth let the brace nest into standard cabinet corner geometry, giving consistent placement along runs. The high impact, specially compounded plastic material supports this fastening workflow by tolerating the forces from staplers and screw guns used in typical shop setups.

Using Hughes Supply Corner Braces In Cabinet Work

Where This Plastic Corner Brace Fits Best

This Hughes Supply corner brace, identified by manufacturer part number PGH445E, fits cabinet corner locations where a compact brace is preferred. The brace is 3-5/8 inches long and 3/4 inch deep, so it sits along the junction of cabinet sides and bottoms without projecting far into the interior. As part of the Corner Braces and Glue Blocks product class, it is suited to reinforcing box construction where cabinet components meet at right angles. The translucent plastic material helps the brace blend inside cabinets that may be finished in lighter tones, which keeps hardware visually low-profile on open interiors. Because it can be stapled through and will also accept glue, it fits both production shop processes using fasteners and adhesive-focused assembly workflows on cabinet jobs.

Why These Corner Brace Details Improve Workflow

The high impact, specially compounded plastic material means the brace works with staplers commonly used in cabinet shops, reducing interruptions from cracked parts when fastening. Plastic that can be stapled through without shattering lets crews drive fasteners rapidly through the brace and into cabinet members, keeping box assembly output steady. The ability to accept glue gives another bonding path, so assemblers can apply adhesive to increase joint integrity without changing the basic hardware layout. Off-center screw holes are laid out to provide easier screw gun access into the corner of the cabinet, which supports more accurate screw placement and helps reduce driver cam-out when working close to side panels. The brace dimensions, at 3-5/8 inches long and 3/4 inch deep, give repeatable positioning from cabinet to cabinet, which supports consistent jig use and keeps assembly patterns stable across multiple units in a run.

Common Questions About This Plastic Corner Brace

Select This Corner Brace For Glue And Staple Assembly

This Hughes Supply plastic corner brace is built for cabinet joints where high impact, specially compounded plastic supports everyday stapling and fastening. The brace can be stapled through without shattering and will also accept glue, so crews can pair adhesive and fasteners for reinforced corners. Off-center screw holes provide easier screw gun access into the corner of the cabinet, helping fasteners seat well even in tight interiors. With braces 3-5/8 inches long and 3/4 inch deep, it fits standard cabinet corner layouts without crowding the interior space. Sold in full box quantities only, it suits production and repeat shop work where consistent parts streamline assembly.