
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Polished brass cabinet pull from the Conquest collection gives a cabinet door or drawer a bright brass look that pairs with traditional decorative hardware. The zinc die cast construction forms a rigid handle that supports everyday opening and closing in kitchens, baths, or built-ins. The 3 inch center to center drilling sets mounting holes at a common cabinet spacing, which matters when aligning multiple pulls across doors and drawers. A 5 inch overall length creates a balanced grip area that fits standard cabinet fronts without crowding adjacent hardware. The 1 inch projection stands the pull off the surface enough for fingers to wrap around, helping users get a solid hold without scraping knuckles on the face. An 11/16 inch width keeps the profile slim so the pull sits neatly on narrow rails while still reading as a defined handle.
The 3 inch center to center measurement defines the drilling distance for this pull, guiding hole layout on new cabinet doors or drawer fronts so hardware lines up across a run. With an overall length of 5 inches, the pull extends past the hole centers on each side, which helps cover minor drilling variation while still presenting an even reveal at the door edge. The 1 inch projection sets how far the grip stands off the face, which informs clearance when planning drawer stack spacing or adjacent door reveals. An 11/16 inch width keeps the footprint narrow, giving layout room on slender rails where wider hardware would crowd panel details or neighboring components. Together, these dimensions support a clean, repeatable mounting pattern on standard cabinetry.
The Conquest series 3 inch center to center pull fits cabinet doors and drawers that follow standard drilling for decorative handles and pulls. Its 5 inch overall length suits typical base and wall cabinet fronts where a mid-size pull looks proportionate on both smaller and wider faces. The polished brass finish pairs naturally with bright brass hinges or latches described as bright or polished brass in the same project, allowing the pull to act as the visible linkage across different hardware points. As a zinc die cast handle classified under decorative hardware and moldings, it works in built-ins, vanities, or storage pieces where matched hardware contributes to a finished, intentional appearance on visible fronts. The 1 inch projection provides clearance that supports use on deeper drawer boxes as well as lighter doors.
The 3 inch center to center drilling is a repeatable standard, so once that measurement is established on a template or jig, the same layout can be run across doors and drawers using this pull without changing settings. A 5 inch length around those same hole centers leaves consistent overhang to each side, which helps installers visually balance hardware relative to the stile or drawer edge. The combination of 1 inch projection and 11/16 inch width sets a predictable envelope for how far the handle extends into the room and across the face, simplifying planning when placing multiple pulls close to inside corners or adjacent appliances. Zinc die cast construction supports uniform sizing from piece to piece, so rows of Conquest pulls align cleanly when mounted at matching heights and offsets. The polished brass finish visually emphasizes those neat lines, highlighting straight runs and even spacing on doors and drawers.
The P14444-3 pull is a Hickory Hardware Conquest series cabinet handle made from zinc die cast with a polished brass finish, suited to decorative hardware and moldings projects.
The pull has a 3 inch center to center dimension, which sets the spacing between mounting holes and supports alignment with other 3 inch cabinet pulls.
The Conquest polished brass pull measures 5 inches in overall length and 11/16 inch in width, giving a slim profile with a full-length grip for cabinet doors and drawers.
The cabinet pull projects 1 inch from the mounting surface, providing finger clearance while keeping the handle close to the door or drawer face.
The P14444-3 cabinet pull is made from zinc die cast material, giving a solid molded handle shape under its polished brass finish.
This pull is part of the Hickory Hardware Conquest collection under the Belwith Keeler brand, aligning it with matching decorative handles and pulls.
The Conquest series polished brass cabinet pull brings a 3 inch center to center layout, 5 inch overall length, and 1 inch projection into one consistent handle for doors and drawers. Zinc die cast construction and the polished brass finish present a unified look from piece to piece, which helps carry a continuous brass line across cabinets, vanities, or built-ins. For projects calling for bright brass decorative hardware and moldings, this Belwith Keeler pull, part number P14444-3, offers defined dimensions that support clean drilling patterns and aligned hardware runs on finished work.