
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Bosch face frame router bit lets you flush a face frame to a cabinet side while simultaneously cutting a V-groove down the joint. This combined operation brings the frame and case side into one clean plane and adds a defined groove line at the seam. The bit is designed specifically for face frame and cabinet side joints, so each pass targets that transition area instead of generic profiling. With a 1/2 inch diameter, the cutting profile stays compact enough for typical cabinet rails and stiles while still creating a visible groove. As a profiling router bit, it shapes the face of the workpiece rather than boring, which fits common face frame building workflows in a cabinet or woodworking shop.
This face frame V-groove router bit is part of the profiling class, so it works in a router setup focused on edge and face shaping rather than drilling tasks. When used to flush a face frame to a cabinet side, the bit runs along the joint where the frame meets the case, trimming the projecting edge into line with the cabinet side. At the same time, its profile forms a V-groove down that seam, so the operator controls both flatness and appearance in one guided pass. As a Bosch router bit, it fits into a router collet appropriate for the bit shank, then runs across the cabinet assembly on a bench or fixture as part of the normal building sequence.
The Bosch Face Frame V-Groove Bits 1/2 inch Diameter are intended for working where a face frame meets a cabinet side. In that location, the bit flushes the frame to the cabinet side and cuts a V-groove down the joint. Cabinet makers can run this profile along the vertical or horizontal seams of framed cabinets to establish both alignment and a defined visual break. The bit also serves when a decorative V-groove is desired on suitable work surfaces, so the same tool can be used to echo that detail across matching fronts. Because the bit belongs to the Bits, Blades and Cutters profiling category, it suits edge and face shaping tasks common in cabinet shops and woodworking environments.
By flushing the face frame to the cabinet side at the same time it cuts a V-groove down the joint, this Bosch face frame router bit turns two joint-finishing steps into one routing pass. The face frame trim action brings the frame and case side into a single plane, which supports tight door reveals and cleaner side views on installed cabinets. The V-groove down the joint then adds a deliberate line that visually organizes the seam, instead of leaving a flat, hard-to-hide glue line. Using this carbide tipped bit means the cutting edges are designed to hold up across repeated joints and decorative V-groove runs, which supports consistent profiles when building multiple cabinets or matching sections within a project.
The Bosch 85647M face frame router bit is used to flush a face frame to a cabinet side while simultaneously cutting a V-groove down the cabinet joint, finishing the seam in one routing pass.
The face frame V-groove router bit cuts a groove down the cabinet joint, defining the seam between frame and side, which gives a deliberate visual line while the frame is trimmed flush.
The Bosch face frame router bit is also used for a decorative V-groove cut, so it can add matching V lines across doors, rails, or panels where that profile is desired.
The 1/2 inch diameter describes the cutting profile size of the Bosch face frame router bit, keeping the groove and trim action sized for typical face frame widths and cabinet seams.
The Bosch 85647M router bit is described as carbide tipped, meaning the cutting edges are designed for wear resistance during repeated routing on cabinet-grade materials and hardwood face frames.
This profiling router bit runs along the face frame and cabinet side joint after assembly, trimming the frame flush and cutting the V-groove so the seam is finished before final fitting.
The Bosch face frame router bit with 1/2 inch diameter is tailored for joints where a face frame meets a cabinet side and for decorative V-groove cuts. Its carbide tipped construction and combined flush trim and V-groove profile help streamline cabinet joint finishing and repeat decorative lines across related parts. For cabinet and woodworking projects built around face frames and profiled fronts, this bit provides a focused way to handle seam trimming and V-groove details in the same routing pass.
Sold In: 1 Each