
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Pro Value Series 20 inch drawer slides use a full extension ball bearing design so drawers travel the full 20 inch length, giving clear access to stored contents in everyday cabinet use. The 100 lb weight rating supports typical residential and light commercial drawer loads while maintaining consistent movement under load. A 1/2 inch plus 1/32 inch -0 side clearance requirement sets a clear target for cabinet and drawer sizing, helping installers plan the fit between case and box. The unhanded side mount layout allows the same DSPRO2.0-20BK slide to install on either side, reducing part sorting on the job. Cold rolled steel construction provides a solid steel track for the ball bearings, supporting the slide structure. The black finish gives a dark, uniform look that can match black casework or hardware schemes in visible applications.
The DSPRO2.0-20BK slide uses a side mount configuration, so the members fasten to the cabinet sides and drawer sides, aligning with common case construction. A 1/2 inch plus 1/32 inch -0 side clearance spec between the drawer and cabinet opening guides the installer to size drawer widths for proper tracking. The 32mm pattern gives a familiar hole layout for those using 32mm cabinet systems, supporting repeatable mounting positions along cabinet sides. Lever disconnect allows the drawer member to separate from the cabinet member, which can simplify handling when building or finishing drawer boxes away from the cabinet.
These full extension ball bearing drawer slides fit side mount drawer applications that call for a 20 inch length and a 100 lb weight rating, matching many kitchen, bath, or utility cabinet layouts. The 1/2 inch plus 1/32 inch -0 side clearance works with standard framed or frameless openings that are laid out around that gap, so existing cabinet practices transfer directly. A 32mm pattern offers alignment with system-bored case sides, keeping the slide positions consistent from cabinet to cabinet. The unhanded design means the same Pro Value Series member works on both left and right sides, which simplifies stocking and reduces mismatched pairs.
Continuous bearings inside the slide support the drawer along its travel, which promotes smooth and quiet performance as drawers cycle under load. Full extension movement brings the drawer box fully forward, giving access to stored items without reaching over the cabinet face. Cold rolled steel construction gives the ball bearings a rigid channel, supporting alignment over the 20 inch length. The black finish offers a uniform dark appearance that can visually blend with dark interiors or hardware schemes where exposed slides might be visible. Lever disconnect lets the drawer member release from the cabinet member, which can aid in installing the cabinet members first and then hanging finished drawers later, helping maintain clean finishes during casework handling. Fixed rear brackets are available, which supports rear mounting approaches where cabinet design calls for bracket attachment at the back.
The DSPRO2.0-20BK is a Pro Value Series 20 inch full extension standard ball bearing side mount drawer slide, so drawers open the full length on ball bearing runners.
These drawer slides have a 100 lb weight rating and a 20 inch length, so they suit drawers sized around 20 inches deep within that load range.
These side mount slides specify 1/2 inch plus 1/32 inch -0 side clearance, which drives the required gap between the drawer box and the cabinet opening.
These slides use a 32mm pattern, so the hole layout lines up with common 32mm cabinet construction systems for repeatable mounting positions.
The slides are made from cold rolled steel with a black finish, giving a steel track with a dark appearance for cabinet interiors or exposed areas.
These slides list recommended fasteners as #8 x 7/16 inch Phillips pan head (WW46000), guiding screw selection for mounting to cabinet and drawer members.
Choosing the Pro Value Series DSPRO2.0-20BK full extension ball bearing drawer slides gives a 20 inch side mount option with a defined 100 lb rating, a 1/2 inch plus 1/32 inch -0 side clearance, and a 32mm pattern that aligns with system-bored cabinet work. For projects planned around a dark finish and unhanded left-right use, these cold rolled steel black slides offer a clear, documented set of dimensions and mounting details to build into your next cabinet run.
Sold In: 20 Set
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1000 Each | WW46000 Mfr# 3670000235961 1000 | Würth #8 x 7/16" Truss Head Hinge and Drawer Slide Installation Screw Phillips Drive - Sharp Point Coarse Thread Zinc, 3670000235961 1000 - 1000/Box |