Kitchen Kompact Chadwood base cabinet is an 18 inch wide, 34-1/2 inch high, 24 inch deep base cabinet built for standard kitchen layouts where precise sizing keeps runs on dimension. The cabinet is a recessed panel style, so the look stays clean while still matching traditional red oak grain in most jobs. Door frames use mortised and tenoned construction in solid 3/4 inch oak, which locks the joints mechanically and supports long-term door alignment under daily use. Flat panel plywood inserts are three-ply with a rotary cut red oak veneer face, giving a real-wood appearance while keeping the panel stable. Solid wood hanging strips at the top and bottom provide solid fixing points to wall framing, which supports accurate installation. A four step process of stain, sealer, sanding, and catalyzed top coat is applied, building a consistent finish that helps the cabinet surface handle normal kitchen wear.
The Kitchen Kompact 18 inch base cabinet dimensioned at 34-1/2 inches high and 24 inches deep aligns with typical countertop and appliance depths, so it integrates into straight or corner runs without special shimming. Solid wood hanging strips located on the top and bottom give installers continuous backing for fasteners along both edges, supporting firm racking control when pulling boxes into line. Plywood drawers are standard, and the front to back epoxy-coated drawer system is securely attached to a solid wood strip in the back of the cabinet, which stabilizes drawer movement so adjustments at the front hold position. Drawers use a ball bearing operated nylon roller system, which guides drawers smoothly along their travel, aiding accurate alignment of faces during final tuning. Concealed, self-closing hinges on the oak flat panel doors keep hardware hidden from view while pulling doors shut, which helps doors sit consistently against the face frame after alignment.
This Kitchen Kompact Chadwood 18 inch base cabinet with recessed panel front fits into layouts needing a narrower base cabinet, such as between appliances or next to corners, while still matching the Chadwood door style. Oak flat panel doors and flat panel plywood inserts with a rotary cut red oak veneer face carry the same species and visual, so long walls of cabinets keep a unified look when paired with other Chadwood units. Solid wood toe kicks at 3/4 inch thick create a sturdy base line along the floor, supporting standard toe space treatments while withstanding daily contact along traffic paths. Adjustable shelves inside let installers or end users set interior spacing to suit stored items, which can help keep tall items or stacked goods organized without cabinet modifications. Plywood drawers standard on this cabinet contribute to a rigid drawer box structure, supporting typical kitchen load demands across the drawer width. The front to back epoxy-coated drawer system, secured to a solid wood strip in the rear, ties drawer movement back into the cabinet box, which can help keep drawer fronts aligned even as loads change over time.
Door frames built from solid 3/4 inch oak using mortised and tenoned construction give the hinges a solid anchor point, which supports consistent reveals when adjusting the concealed, self-closing hinges. The concealed hinge design keeps the hardware hidden while allowing the self-closing feature to pull doors to the face, which helps maintain uniform gaps along a run after setup. The ball bearing operated nylon roller system under the drawers guides motion smoothly, making it easier to judge and fine-tune drawer front alignment relative to doors and adjacent cabinets. Solid wood hanging strips located on the top and bottom provide continuous fastening structure, helping installers draw multiple cabinets into a straight, plumb line with less risk of crushing the cabinet back. The four step finish process of stain, sealer, sanding, and catalyzed top coat builds a protective layer over the oak and veneer surfaces, allowing the installed cabinet faces to handle normal kitchen contact while keeping the grain definition visible. Together, these construction details support repeatable installation results across projects that use the Chadwood line.
The Kitchen Kompact Chadwood base cabinet measures 18 inches wide, 34-1/2 inches high, and 24 inches deep, so it fits standard base cabinet and countertop layouts in most kitchen runs.
The cabinet uses oak flat panel doors with door frames made from solid 3/4 inch oak and flat panel plywood inserts with a rotary cut red oak veneer face, giving a recessed panel oak appearance.
Door frames use mortised and tenoned construction in solid 3/4 inch oak, which creates strong joints that help doors stay square and maintain alignment during everyday kitchen use.
The Chadwood base cabinet doors use concealed, self-closing hinges, so the hardware stays hidden while the self-closing action helps doors pull tight to the face after opening.
Drawers are plywood with a front to back epoxy-coated drawer system securely attached to a solid wood strip at the back, working with a ball bearing operated nylon roller system for smooth travel.
The cabinet receives a four step process of stain, sealer, sanding, and catalyzed top coat, producing a consistent finish that helps the oak and veneer surfaces handle normal kitchen wear.
This Kitchen Kompact oak base cabinet in the Chadwood style pairs an 18 inch width with 34-1/2 inch height and 24 inch depth, giving a standard-size base unit that fits many layout gaps. Mortised and tenoned 3/4 inch solid oak door frames, oak flat panel doors, and three-ply plywood inserts with red oak veneer support a coordinated appearance when combined with other Chadwood pieces. With plywood drawers, a ball bearing operated nylon roller system, adjustable shelves, and solid wood toe kicks, this CW18B cabinet offers a practical building block for full kitchen runs or targeted replacements. Use these verified construction and dimension details to match this base cabinet to the specific bay in your next Kitchen Kompact Chadwood installation.
Sold In: 1 Each