Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Glenwood vanity drawer base describes this Kitchen Kompact 15 inch wide, 34-1/2 inch high, 21 inch deep recessed panel vanity drawer base that provides a defined footprint for planning plumbing and counter layouts. The solid 3/4 inch wood frames create a rigid cabinet structure, which supports alignment when setting adjacent units and helps doors and drawers stay properly fitted over time. All frames are built of solid 3/4 inch oak, maple or beech, so the face frame presents a hardwood surface ready for finishing systems suited to these species. The recessed panel Glenwood style gives the front a framed look, which helps tie this base into matching Kitchen Kompact Glenwood pieces on the same run. The vanity base format concentrates storage and drawer function in a 15 inch width, which helps use narrow spaces effectively while keeping a standard 34-1/2 inch height for top and sink planning.
The 15 inch width, 34-1/2 inch height, and 21 inch depth give predictable case dimensions, which simplifies laying out wall conditions, plumbing clearances, and countertop overhang on drawings and on site. Solid 3/4 inch frames in oak, maple or beech create consistent screw-holding material around the front, so installers can fasten adjoining cabinets through the face frame with reduced risk of crush or strip. Each rail being kiln-dried and joined by mortise and tenon before gluing forms a rigid rectangle, which helps the cabinet stay square as it is pulled into plane with shims and fasteners. Solid wood corner blocks that are glued and power nailed stabilize the carcass, supporting racking loads when the cabinet is slid, lifted, and set. The 3/4 inch solid wood toe kick gives a solid bearing edge for shims along the floor line, helping fine-tune level and front-to-back pitch.
This Kitchen Kompact Glenwood 15 inch wide vanity drawer base fits runs where a narrow cabinet must still provide drawer storage and a full 34-1/2 inch finished height for a vanity top. The 21 inch depth aligns with standard vanity depths, which supports using common tops and maintaining front flush lines with neighboring cabinets built to the same dimension. All frames built of solid 3/4 inch oak, maple or beech allow this base to sit next to other hardwood-faced cabinets while keeping species continuity along the wall. The recessed panel Glenwood styling coordinates with other Glenwood pieces referenced by the GLENWOOD V15DT and GWV15DT descriptions, so an entire bathroom or related area can carry the same frame-and-panel look. Solid wood toe kicks at 3/4 inch thickness support a stable stance on typical bathroom flooring.
Each rail being kiln-dried, mortise and tenon joined, and glued creates a frame that resists seasonal movement more predictably than looser joints, which supports long-term alignment of doors and drawer fronts mounted to the face frame. Solid wood corner blocks that are glued and power nailed at the corners keep the box square as fasteners are driven, so installers can pull multiple cabinets together without fighting twist at each joint. Solid wood hanging strips on base cabinets at the top and bottom give clearly defined fastening zones, which streamlines locating studs and driving structural screws through continuous solid wood. End panels using 3-ply construction with a 1/2 inch engineered wood core and hardwood veneers provide a balanced side panel that accepts typical cabinet fasteners at the edges while presenting a hardwood veneer face for visible ends. These combined details allow the Glenwood vanity drawer base to be integrated into a run with predictable behavior during leveling, scribing, and fastening.
The Glenwood vanity drawer base measures 15 inches wide, 34-1/2 inches high, and 21 inches deep, which supports standard vanity top depths and typical bathroom counter heights.
The cabinet frames are built of solid 3/4 inch oak, maple or beech, providing a hardwood face frame that helps maintain rigidity and alignment when tying cabinets together.
Each rail is kiln-dried, joined by mortise and tenon, and glued, creating strong joints that help the frame stay square during handling, leveling, and fastening.
Solid wood corner blocks are glued and power nailed at the corners, bracing the case so it resists racking when the vanity base is moved and secured on site.
End panels use 3-ply construction with a 1/2 inch engineered wood core and hardwood veneers, giving a stable side panel with a hardwood-faced exterior for visible ends.
The 3/4 inch thick solid wood toe kick provides a strong base area for shimming and floor contact, helping maintain level and frontal alignment under normal vanity loads.
The Kitchen Kompact Glenwood GWV15DT vanity drawer base ties a 15 inch width, 34-1/2 inch height, and 21 inch depth to solid 3/4 inch hardwood frame construction, so it fits standard vanity layouts while supporting face frame alignment along the run. Kiln-dried mortise and tenon frame rails, solid wood corner blocks, and 3/4 inch solid wood toe kicks build a rigid cabinet that responds predictably when leveled, shimmed, and fastened. End panels with a 3-ply, 1/2 inch engineered wood core and hardwood veneers present a hardwood exterior wherever a side is exposed. When a project calls for a recessed panel Glenwood vanity drawer base in this size, this unit provides defined dimensions and construction details to plan around confidently.
Sold In: 1 Each