Kitchen Kompact Warmwood vanity sink base defines a 36 inch wide, 34-1/2 inch high, 21 inch deep sink cabinet that is sized for typical vanity layouts, so it fits common bathroom runs while leaving room for plumbing and countertop overhang. The solid 3/4 inch hardwood frame gives the cabinet a rigid front structure that holds doors and false fronts in alignment over time, which helps doors close consistently after repeated use. Each frame rail is kiln-dried, joined with mortise and tenon joints, and glued, creating tight, stable joints that resist movement from seasonal humidity. Solid wood corner blocks are glued and power nailed at stress points, tying the sides to the frame to support everyday loads. Solid wood hanging strips at the top and bottom of this base cabinet give a solid connection surface to supporting structure along the back, helping the cabinet sit square. The recessed panel Warmwood styling provides a coordinated look when used with other Kitchen Kompact cabinets in the same line.
This Kitchen Kompact vanity sink base uses a solid 3/4 inch hardwood frame, so the front of the cabinet provides a firm reference when aligning adjoining cabinets in a run. The mortise and tenon, kiln-dried, and glued rails form a square face opening, which supports accurate placement of sinks and tops. Solid wood hanging strips located at both the top and bottom of the base cabinet give continuous solid backing where fasteners engage supporting structure, helping the cabinet sit tight against surfaces without shimming at random points. Solid wood toe kicks extend across the front, which carries the weight of countertops and sinks down to the floor in a continuous line. End panels built with a 1/2 inch engineered wood core and hardwood veneers maintain panel flatness along the sides, assisting with tight seams when aligning adjacent cabinetry.
The WWV36SDLT vanity sink base, at 36 inches wide by 34-1/2 inches high by 21 inches deep, works in layouts calling for a standard-width sink cabinet, so it suits many single-bowl bathroom designs. The recessed panel style in the Warmwood series aligns visually with other Kitchen Kompact cabinets in the same collection, allowing consistent fronts across a full room of cabinetry. Solid wood toe kicks at the front give the cabinet a defined footprint, useful when planning floor transitions up to the cabinet face. Solid wood hanging strips on this base cabinet, positioned at the top and bottom, span the width of the back to give repeatable fastening points along the wall line, which matters when installing multiple units side by side. End panels built with a 3-ply, 1/2 inch engineered wood core with hardwood veneers provide stable sides that work well between other cabinets or exposed ends.
The solid 3/4 inch hardwood frame on this Kitchen Kompact Warmwood vanity sink base provides a stiff front plane, which helps installers keep reveal lines even when tying it into nearby cabinets. Kiln-dried rails joined with mortise and tenon construction and glued joints reduce movement at the frame, so door and drawer openings stay consistent, aiding in predictable hardware alignment. Solid wood corner blocks that are glued and power nailed lock the frame to the cabinet body, which supports sink and top loads by distributing stress into the sides and bottom. Solid wood toe kicks give a continuous, load-bearing front edge that supports the weight above without relying only on thin panel stock. Solid wood hanging strips on the base cabinet, located at the top and bottom, supply reliable fastening zones, which makes it easier to repeat a consistent fastening pattern along the project. The 3-ply, 1/2 inch engineered wood core end panels with hardwood veneers resist warping, contributing to square openings that simplify top and sink placement.
The WWV36SDLT Warmwood vanity sink base measures 36 inches wide, 34-1/2 inches high, and 21 inches deep, which fits many standard bathroom vanity layouts and common countertop depths.
This Kitchen Kompact vanity sink base uses a solid 3/4 inch hardwood frame with kiln-dried rails joined by mortise and tenon joints and glued, giving a rigid face frame that helps keep doors aligned.
The Warmwood vanity sink base uses solid wood corner blocks that are glued and power nailed, tying the frame and sides together to better handle sink and countertop loads.
The cabinet uses solid wood toe kicks and solid wood corner blocks, which together help carry vertical loads from the countertop and sink down to the floor and into the cabinet structure.
End panels use 3-ply construction with a 1/2 inch engineered wood core and hardwood veneers, providing dimensionally stable sides that help the cabinet stay square in typical installations.
This base cabinet has solid wood hanging strips located at the top and bottom, offering continuous solid material along the back for fastening to supporting structure.
The Kitchen Kompact Warmwood vanity sink base WWV36SDLT combines a solid 3/4 inch hardwood frame, mortise and tenon kiln-dried rails, and solid wood corner blocks in a 36 inch wide by 34-1/2 inch high by 21 inch deep cabinet, giving a rigid structure ready for typical vanity layouts. Solid wood toe kicks and solid wood hanging strips at the top and bottom of the base cabinet create dependable support and fastening areas for full runs of cabinetry. End panels with a 3-ply, 1/2 inch engineered wood core and hardwood veneers add dimensional stability along the sides, supporting square openings for tops and sinks. For projects calling for a Warmwood recessed panel look with this construction detail, this cabinet provides a consistent, job-site oriented option.
Sold In: 1 Each