Bostik TG4 Heavy Duty Applicators are hotmelt adhesive applicator guns designed for product assembly and packaging applications, so they support repetitive bonding work in a shop or on a light industrial line. The tool operates at 380 F operating temperature, which allows common hotmelt sticks to reach a workable melt for consistent bead or dot application on substrates. Output per hour of 3-5 lb. means the gun can dispense a substantial volume of adhesive in a shift, which matters when multiple joints or cartons must be bonded without frequent pauses. Power (120V) at 100W lets the gun run from standard power circuits in many work areas while supplying steady heat to the melt chamber. Use of 7/16 - 1/2 inch diameter sticks fits widely available stick sizes, which simplifies stocking a single adhesive format across benches.
The THERMOGRIP hotmelt glue gun operates at 380 F operating temperature, so the internal heater brings adhesive sticks to a flowable state suitable for controlled dispensing through the nozzle during use. Power (120V) at 100W supports this heating profile while drawing from typical power sources found in many woodworking or assembly environments. Output per hour of 3-5 lb. reflects the rate at which adhesive can be delivered once molten, which matters when planning cycle times for assembly stations or packing lines. The design use of 7/16 - 1/2 inch diameter sticks defines the adhesive feed size, guiding selection of compatible hotmelt sticks for uninterrupted operation.
The Bostik TG4 Heavy Duty Applicators sit within the hotmelt adhesive applicator guns class, positioning them for tasks that rely on molten adhesive rather than solvent or water-based systems. They are designed for product assembly applications, which can include bonding components, fixtures, or subassemblies before downstream operations. The design also addresses packaging applications, so the same hotmelt gun can be used when sealing cartons or cases coming off woodworking or fabrication lines. Operating at 380 F operating temperature, the gun supports adhesive behavior suited to these roles by maintaining a molten state during active use. Output per hour of 3-5 lb. further aligns with these environments by supplying enough adhesive volume to keep pace with moderate production runs.
The THERMOGRIP hotmelt glue gun power (120V) at 100W allows the heating element to maintain the 380 F operating temperature profile, which supports steady viscosity and predictable flow as the trigger is cycled repeatedly during assembly or packing tasks. This steady condition helps maintain uniform bead size and coverage, which supports consistent bond lines across multiple parts or cartons. Use of 7/16 - 1/2 inch diameter sticks provides a defined feed path, so each stroke advances a known mass of adhesive through the chamber, contributing to repeatable output per hour of 3-5 lb. That rated output gives planners a reference point when aligning station throughput expectations with adhesive delivery capacity. A warranty: 6 months gives a stated support period for the THERMOGRIP hotmelt glue gun, which matters when adding it to shop equipment that runs daily work.
The Bostik TG4 Heavy Duty Applicators are hotmelt adhesive applicator guns, so they are used to apply molten adhesive for bonding in product assembly and packaging workflows.
The THERMOGRIP hotmelt glue gun is designed for product assembly and packaging applications, supporting both component bonding and carton sealing in shop or light industrial environments.
The THERMOGRIP hotmelt glue gun operates at 380 F operating temperature, providing a consistent melt range for controlled adhesive flow during continuous use.
The Bostik TG4 Heavy Duty Applicators have an output per hour of 3-5 lb., supporting moderate production rates in assembly stations or packing lines.
The hotmelt adhesive applicator gun uses power (120V) at 100W, so it operates from many standard electrical circuits in woodworking and assembly areas.
The THERMOGRIP hotmelt glue gun uses 7/16 - 1/2 inch diameter sticks, allowing use of commonly available hotmelt stick sizes for ongoing adhesive supply.
The Bostik TG4 Heavy Duty Applicators combine their role as hotmelt adhesive applicator guns with an output per hour of 3-5 lb., making them suited to shops that run repeated product assembly and packaging tasks. Operating temperature of 380 F and power (120V) at 100W provide a defined heating profile that supports stable adhesive flow during extended use. Use of 7/16 - 1/2 inch diameter sticks further aligns the tool with standard hotmelt formats already stocked in many operations. For woodworkers and assemblers who rely on hotmelt bonding in daily work, this THERMOGRIP hotmelt glue gun offers a clearly specified tool choice grounded in these operating details.
Sold In: 1 Each