Material handling cart from Paintline gives shops a single rolling platform to move panels and parts through production, so parts stay together and travel cleanly between work areas. This lateral panel cart uses a powder-coated steel base, which provides a rigid frame that stays stable under load in daily use. An MDF decking surface supports flat parts across the base, so sheets, doors, or components rest evenly instead of point-loading on rails. Heavy duty 6 inch casters under the base let the cart roll smoothly around the shop, so operators can redirect work-in-process without lifting or repiling material. The cart is designed to handle multiple parts at once as you move through the shop or production, which keeps batches organized from one station to the next. The overall design supports material handling tasks in paint, stain, or general fabrication workflows.
This Paintline lateral panel cart uses removable dividers that can be installed along the width or length of the cart, so the internal layout can be adjusted to match current jobs. When dividers are in place, they segment the MDF deck into as many as 12 bins, which helps keep narrow rails, wide panels, and small parts standing in organized rows during movement. When all dividers are removed, the same frame and MDF decking act as a lumber cart, so long stock or stacked sheets can be stored and rolled on a single open platform. The 22 inch overall width lets the cart move through congested aisles, so it fits between existing machines or racks while still leaving walking space. Heavy duty 6 inch casters support turning and repositioning, so the cart can be oriented wherever loading or unloading is most efficient.
This versatile material handling cart is designed to handle multiple parts as you move through the shop or production, so it fits well anywhere panels or components need to travel between work steps. In finishing areas, the lateral panel cart keeps painted or stained parts on the MDF decking, so pieces rest on a flat support while they move between application, drying, and prep zones. In machining or assembly zones, the removable dividers can be arranged along the width or length of the cart to hold groups of doors, frames, or panels in as many as 12 bins, so each job stays separated while still sharing a single rolling base. The 22 inch width works well in congested aisles, so the cart can travel between equipment rows, storage racks, or work tables without needing extra clearance. When work shifts from panel handling to long-stock handling, removing all dividers converts the frame into a lumber cart, so boards or bundled material can roll through the same narrow aisles using the same footprint. The overall design supports workflows in paint and stain environments, matching its classification within paint and stain supplies.
The powder-coated steel base under this PROCART material handling cart provides a stable platform, so the frame resists flex as loads approach the 2,000 lbs capacity, which helps parts stay upright and aligned in their dividers. MDF decking across the base spreads each piece over a broad surface, so workpieces experience uniform support instead of resting on sparse crossbars, which helps reduce edge marking while they are rolled. Removable dividers that install along either width or length allow repeatable spacing setups, so shops can standardize bin layouts for common job types and reuse them whenever similar batches run again. The ability to configure as many as 12 bins means small to medium parts can be grouped tightly, so operators can visually confirm that each slot stays filled or emptied as work advances. Heavy duty 6 inch casters contribute to predictable movement, so even with substantial loads, the cart tracks smoothly and pivots where floorplans demand tight turns. The 22 inch width interacts with these casters to keep the center of mass over a compact base, so the cart navigates congested aisles while maintaining stable rolling behavior during typical shop handling.
The PAPROCART-2 material handling cart is designed to handle multiple parts as you move through the shop or production, supporting panel, component, or lumber movement between work steps.
The lateral panel cart uses MDF decking over a powder-coated steel base, so panels and parts rest on a continuous, stable surface while they are rolled through different shop areas.
The material handling cart has a 2,000 lbs weight capacity, so it can transport heavy batches of panels or lumber on a single platform during typical shop handling.
The removable dividers can be installed along the width or length to create as many as 12 bins, so the cart layout adapts to different part sizes and job groupings.
This cart serves as a lumber cart when all dividers are removed, so long boards or stacked sheets can be staged and moved on the open MDF-deck platform.
The 22 inch width works well in congested aisles, so the cart moves between machines or racks while still carrying useful loads on its MDF deck.
The Paintline PAPROCART-2 material handling cart combines a powder-coated steel base, MDF decking, and heavy duty 6 inch casters to move heavy parts efficiently. Removable dividers that form up to 12 bins let one cart manage panels, components, or lumber. The 22 inch width works well in congested aisles, so it fits established shop layouts while still carrying substantial loads. For shops needing a lateral panel cart that also functions as a lumber cart, this PROCART material handling cart aligns closely with everyday paint, stain, and fabrication workflows.
Sold In: 1 Package