Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Formica IdealEdge 9529-46 Sea Salt provides a decorative laminate edge molding that finishes exposed edges on laminate surfaces for a unified look. The Sea Salt Etchings finish gives the edge the same visual character identified by the 9529-46 design, so the profile reads as one continuous surface from top to edge on counters, panels, or shelves. The waterfall edge molding profile forms a smooth, flowing transition, which helps reduce sharp visual breaks along the edge and supports a more finished appearance in kitchen, bath, or commercial laminate runs. At 1-1/2 inches high, this molding is sized to cover typical laminate build-ups, allowing installers to hide substrate edges while keeping the line consistent. The 144 inch length supports long straight runs in a single piece, helping limit joints and alignment breaks along the edge.
The 1-1/2 inch height on this Formica laminate edge molding sets a predictable coverage band along the front of a laminate build-up, which helps layout when planning the step between substrate and finished face. The 144 inch length lets installers run the molding along full-size tops or long panels without breaking the line, which simplifies corner planning and miter layout. As a laminate edge molding, it is intended to work in the same general fabrication environment as laminate sheet goods, so fabricators can coordinate cuts and edge profiles using familiar laminate-focused tooling and workflows.
This Formica IdealEdge 9529-46 Sea Salt Etchings finish waterfall edge molding sits in the decorative laminate edge moldings category, placing it squarely in surfacing and countertop work where exposed substrate needs a finished front. Its Sea Salt Etchings finish ties it directly to projects using the 9529-46 design, so tops and vertical surfaces specified with that pattern can carry the same look over the nose. The 1-1/2 inch height supports use on many laminate build-ups in kitchens, baths, and commercial tops, where the vertical reveal needs to cover the edge without appearing oversized. At 144 inches long, a single molding section can span a long run of cabinet or work surface, which is useful in straight reception counters or extended residential islands where a continuous front is important.
The waterfall edge molding profile on this part shapes the front so it flows from the laminate surface into the edge, which helps create a defined yet smooth transition line that reads cleanly after installation. Because the molding is classified as laminate edge molding, its behavior aligns with laminate-based fabrication, allowing fabricators to plan cuts, joints, and corner details using similar expectations to sheet laminate. The Sea Salt Etchings finish and 9529-46 designation define the visual match, so specifying this exact part number, 095292046F12000, links the front edge directly to that design callout on drawings. With a 1-1/2 inch height and 144 inch length, installers can balance coverage and seam placement, positioning joints and miters where they work best for the overall layout rather than being driven by short stock.
Formica IdealEdge 9529-46 Sea Salt is a decorative laminate edge molding, so it finishes exposed laminate edges with a matched profile in the Sea Salt Etchings design.
The Sea Salt Etchings finish matches the 9529-46 design, so the edge molding carries the same look as the laminate surface, helping the top and front read as one continuous design.
This waterfall edge molding measures 1-1/2 inches high by 144 inches long, providing coverage for laminate build-ups and enough length for extended straight runs.
This laminate edge molding is used on laminate countertops and decorative surfaces where the front edge needs a finished Sea Salt Etchings waterfall profile matching the 9529-46 design.
The manufacturer part number 095292046F12000 identifies this specific Formica IdealEdge Sea Salt Etchings finish waterfall edge molding, tying the exact profile, finish, and size to project documentation.
The waterfall profile creates a smooth, flowing front edge, which reduces harsh transitions from the laminate surface and supports a more continuous, finished appearance on countertops.
Choose the Formica IdealEdge 9529-46 Sea Salt Etchings finish waterfall edge molding when the project calls for a 1-1/2 inch high, 144 inch long laminate edge that visually ties to the 9529-46 design. Its decorative laminate edge molding construction and waterfall profile give installers and fabricators a defined way to finish front edges on laminate-based tops while maintaining a consistent Sea Salt appearance along the full run.
Sold In: 1 Each