Rehau PVC edgebanding 301674-404 is a PVC edge banding from Rehau, Inc. that covers and protects raw panel edges, so cabinet and furniture projects present a finished edge instead of exposed substrate. The product is listed under Edge Banding, which means it is intended to cap the open sides of panels and tops, turning cut edges into a uniform band that visually ties in with the panel surface. The SAP description "15/16X.018 CP40603 LAC 600FT" identifies the nominal width, thickness, and roll length, allowing shops to match this banding to their panel thickness and production run length. The manufacturer part number 301674-404 provides a precise reference for reorders, so repeat jobs can use the same banding and maintain visual consistency across multiple installations.
The SAP description "15/16X.018 CP40603 LAC 600FT" ties directly to fit and processing, because the 15/16 inch width positions the banding to cover common panel thicknesses with enough overhang for trimming while keeping waste low. The 0.018 inch thickness gives installers and fabricators a sense of how the edge will respond to typical edge-band trimming equipment, allowing them to anticipate trimming behavior and flushness. Identifying the material as PVC guides tooling selection toward cutters and trimmers suitable for PVC edges, supporting clean results at the interface between banded edge and panel face.
The product class of Edge Banding and the Rehau PVC edgebanding, 301674-404 name indicate that this banding is used specifically on exposed panel edges in woodworking and casework assemblies, so it fits applications such as cabinet sides, shelves, and furniture components where cut edges need a finished strip. The PVC material designation means it is suited to projects that are already specified for PVC edges, aligning with shop standards that call for this type of banding in laminate or similar panel constructions. The 15/16 inch width referenced in the SAP description allows it to be matched to panel constructions that fall within that coverage range, so edge coverage can be planned according to the panel build-up in a given job. Because the product is identified by manufacturer part number 301674-404, it can be tied directly to drawings or cutlists that call out the same number, helping installers and fabricators match the correct banding to the specified locations.
The nominal 0.018 inch thickness listed in the SAP description gives a predictable profile for trimming, so edge-banders and hand trimmers can be set to remove a small, known amount of material and leave a flush transition to the panel surface. The 600-foot length indicated in the description supports consistent color and material characteristics across a series of cabinets or fixtures, because a single roll can serve many parts in the same run. The clear identification as Rehau PVC Edgebanding, 301674-404 connects jobs back to a specific material reference, so repeat projects can use the same banding and maintain continuity over time. The category placement under Edgebanding reinforces that this product is intended to finish edges rather than act as a decorative surface sheet, supporting clear role separation in shop material planning.
Rehau PVC edgebanding 301674-404 uses the 15/16X.018 size to indicate a nominal 15/16 inch width and 0.018 inch thickness, which guides matching to panel thickness and trimming setup.
Rehau PVC edgebanding 301674-404 in a 600-foot length supports extended runs or multiple projects from one roll, reducing mid-job roll changes during cabinet or furniture production.
Rehau PVC edgebanding 301674-404 is identified as PVC edgebanding, so it uses PVC as the edge material for finishing exposed panel edges in cabinet and woodworking projects.
Rehau PVC edgebanding 301674-404 is listed as Edge Banding in the Miscellaneous|Edgebanding category, clarifying that it is selected specifically for panel edge treatment tasks.
Rehau PVC edgebanding, 301674-404 uses that part number as a precise identifier, allowing shops to tie drawings, cutlists, and reorders directly to the same edge material.
Rehau PVC edgebanding 301674-404 uses PVC construction, aligning it with projects that specify PVC edge banding on panels, so material choice matches established design standards.
Rehau PVC edgebanding 301674-404 combines a defined 15/16X.018 size with a 600-foot roll length, giving shops a clearly specified PVC edge banding that matches common panel edge needs and supports extended production. The classification as Edge Banding and the manufacturer part number 301674-404 provide straightforward references for purchasing and repeat jobs, so the same material can be matched across multiple projects. For cabinet, furniture, or casework work that calls for PVC edge banding in this size range, this product offers a clearly identified option that aligns with panel edge finishing tasks.
Sold In: 1 Roll