Rehau PVC edgebanding 301674-687 gives you a dedicated edge banding solution from Rehau, Inc., so cabinet and fixture projects can use a consistent source when finishing exposed panel edges. The product class as edge banding defines its role as an applied edge finish, so raw panel cores can be covered in a single material step. The PVC construction provides a uniform synthetic edge, so color and surface remain consistent along the full length of the banded run. The 15/16 inch width stated as 15/16 in the description supports coverage on common panel thicknesses while leaving working tolerance for flush trimming. The .018 thickness provides a thin edge profile, so trimmed edges sit close to the panel face for a low-build look. The 600 ft length listed in the description supports longer production runs, so repetitive cabinet or casework parts can be processed from one continuous coil.
The 15/16 inch width listed in the description gives installers working margin past the panel faces, so edge banders and trimmers can cut back to a precise flush line. The .018 thickness provides a light-gauge PVC strip, so heat and pressure during application act through a relatively thin section for predictable bonding and forming around panel edges. The 600 ft roll length supports longer uninterrupted runs through feed-through edge banding equipment, so setup time between batches stays focused on part changes rather than material changeovers. As part of the edge banding product class, this Rehau PVC strip is sized and formatted specifically for edge application, so it fits naturally into standard edgebanding workflows in woodworking shops.
The category listing as Edgebanding positions Rehau 301674-687 for use on exposed panel edges in cabinetry, casework, and other panel-based assemblies, so raw composite or wood-based substrates can receive a matching edge treatment. The 15/16 inch width supports use on panels near three-quarter thickness, so door and drawer fronts, cabinet sides, and shelving can share a common edge size. The .018 thickness means each edge layer adds only a small build to the panel perimeter, so assembled parts maintain nominal dimensions important to layout and hardware alignment. The 600 ft length makes this roll practical for shop environments that process repeated part sizes, so nested parts from sheet goods can be edged from one continuous supply.
The defined 15/16 inch by .018 dimension in the description provides a known cross-section, so machine settings for trimming, scraping, and profiling can be dialed to a consistent target and reused across jobs. The PVC composition identified in the product name produces a stable synthetic edge, so machining characteristics remain similar from part to part, supporting predictable feed rates and cutter choices. The 600 ft length called out for this product reduces the number of coil transitions across a production run, so variations related to splices or material changes are minimized. The specific manufacturer part number 301674-687 ties every reorder back to the same Rehau specification, so color, texture, and geometry remain aligned from project to project when the same code is used.
Rehau 301674-687 is PVC edgebanding classified under edge banding, so it is intended to finish and protect exposed panel edges in woodworking and cabinet projects.
The Rehau PVC edgebanding has a listed size of 15/16 inch by .018 inch, so it provides slight overhang for trimming while keeping a thin edge profile on finished panels.
The Rehau 301674-687 PVC edgebanding is specified at 600 ft in length, so it supports extended edging runs and repeated cabinet components from a single roll.
This product uses PVC as identified in the name, so the edge presents a homogeneous plastic surface that machines uniformly along rips, corners, and profiles.
The 15/16 inch width supplies a small margin beyond typical panel thicknesses, so trimmers can cut back to a clean, flush edge without exposing the substrate.
The manufacturer part number 301674-687 uniquely identifies this Rehau PVC edgebanding, so future orders can match the same size and specification for repeat work.
The defined 15/16 inch by .018 dimension and 600 ft length make Rehau PVC edgebanding 301674-687 a repeatable choice when setting up edge banding equipment for panel work. Using the same manufacturer part number from Rehau, Inc. across projects keeps the edge material specification consistent as you run new batches of cabinet or casework components. For shops relying on standardized dimensions and stable machining behavior at the panel edge, this dedicated edge banding format supports a steady, predictable edging workflow.
Sold In: 1 Roll