Rehau PVC edgebanding 302164-522 provides a PVC edge treatment from Rehau, Inc. that finishes exposed panel edges so they present as a completed surface in cabinet and woodworking projects. This product is classified as edge banding, so it is intended to cover raw panel edges and visually tie them into the adjoining faces. The 15/16 inch width in the SAP description supports coverage of common 3/4 inch panels while allowing a small trim margin, which matters when dialing in flush, chip-free edges. The .018 inch thickness described in the SAP data gives a relatively thin band, which helps when matching adjacent surfaces without building noticeable bulk at the edge. The CP60588 reference and EMB LAC description give a defined decor and surface style for projects that need consistent appearance across multiple parts. The 600FT reference in the SAP description indicates a long run that supports production work where frequent material changeover would slow the job.
The 15/16 inch width described in the SAP data gives extra coverage beyond typical 3/4 inch panels, allowing installers to trim both sides back to a clean, flush line after bonding. That trimming margin reduces the risk of slight misalignment showing as exposed core or underhang. The .018 inch thickness supports a slim edge profile, which matters when aligning with cabinet doors, drawer fronts, and casework where thicker edges could interrupt reveals. The EMB LAC description in the SAP text identifies a particular surface character, so fabricators can coordinate this banding with matching finishes on adjacent components. The 600FT reference signals a continuous length suited to running multiple parts in sequence, which helps maintain visual consistency across doors, drawers, and panels without switching material mid-job.
The Category listing as Miscellaneous|Edgebanding places Rehau PVC edgebanding 302164-522 in the edge banding segment commonly used on cabinet, furniture, and general woodworking panels. That classification supports use on casework sides, shelves, doors, and drawer fronts where exposed core requires coverage. The 15/16X.018 sizing in the SAP description aligns with many melamine or laminate-on-board constructions based on 3/4 inch cores, so shops can run this band on standard carcass and front components without changing edge setups. The CP60588 EMB LAC designation defines a particular decor and embossed lacquered style, which helps when specifying a uniform look across multiple rooms, units, or production batches that must share the same visual standard.
The manufacturer part number 302164-522 links the physical band to documented specifications, so project drawings or cut lists can call out this exact edge banding when repeatability across releases is important. The 600FT reference supports longer production runs on edgebanders or manual setups, reducing the number of material changes on a line of doors or panels. That continuity matters when maintaining color and texture alignment from one part to the next, especially on visible cabinet runs where mismatched edges would stand out.
The edge banding classification means Rehau PVC edgebanding 302164-522 is designed to operate within established edge banding processes, supporting consistent feed, trimming, and finishing steps across similar materials. The 15/16 inch width offers installers leeway during placement, as the extra fraction of an inch can absorb minor setup variation before final trimming to flush. That margin helps reduce rework from edges that cut short or fail to cover the substrate completely. The .018 inch thickness keeps the transition between face and edge subtle, which is valuable when fitting doors and drawer fronts to tight reveals where heavier edges could influence clearances.
The CP60588 EMB LAC reference in the SAP description signals a controlled decor and surface treatment, so production teams can pair this edge banding with coordinated surfaces for a coherent appearance. The combination of a defined manufacturer, Rehau, Inc., and a unique part number supports accurate material pulls from inventory and consistent replacement on future jobs that need the same look. When runs extend across many components, the 600FT indication helps maintain continuity on a single line of material, which supports stable feed behavior and a repeatable finish from the first piece to the last.
Rehau PVC edgebanding 302164-522 is an edge banding material classified under edge banding, so it is intended to cover and finish exposed panel edges on cabinet and woodworking projects.
The 15/16X.018 size in the SAP description provides slight overhang on 3/4 inch panels and a thin profile, supporting trimming to a flush edge while keeping the edge visually light.
The CP60588 EMB LAC description identifies a specific decor and embossed lacquered style, helping designers and shops match this edge banding to coordinated panel finishes.
The 600FT reference in the SAP description indicates a long length that supports extended production runs, reducing material changeovers during cabinet or furniture edge banding.
Rehau, Inc. as the brand provides a defined manufacturer source, so shops can standardize on this PVC edgebanding line to keep appearance and performance consistent across projects.
Part number 302164-522 uniquely identifies this Rehau PVC edgebanding, which helps drafters, purchasers, and production teams call out and pull the correct material repeatedly.
Rehau PVC edgebanding 302164-522 brings a defined 15/16X.018 format, CP60588 EMB LAC decor, and 600FT run length together for cabinet and woodworking edges that need consistent coverage and appearance. With its classification as edge banding and a clear manufacturer part number, this product fits directly into established shop workflows where precise sizing and repeatable sourcing matter. For projects that rely on matching decor and stable edge profiles from the first panel to the last, this Rehau, Inc. edge banding offers a clearly defined option.
Sold In: 1 Roll