Rehau PVC edgebanding 303334-337 provides a PVC edge banding solution for finishing exposed edges on panels, so cabinet and fixture work gains a consistent, professional look along every run. The edge banding format means you can cover raw board edges in a single, continuous operation, which supports efficient workflow on repetitive casework and shelving. The Rehau, Inc. brand identifies this as part of Rehau's edge banding line, so shops working with Rehau materials can match product families across projects. The product sits in the Edgebanding category, tying it directly to edging tasks rather than general trim work, which helps crews assign it accurately in job planning and material takeoffs.
The stated 1-5/16 inch width gives installers working clearance beyond the panel thickness, so they can set the band flush to one face and trim the excess on the opposite side in a controlled pass. The 3mm thickness provides enough material for edge trimming tools to track without chatter, which supports straighter passes and more uniform reveals along door and panel edges. The 300ft roll length means longer uninterrupted feeds through edgebanding equipment, so operators can run full cabinet runs or banked components with fewer splices to manage at corners or seams.
The product class of Edge Banding defines this Rehau, Inc. piece as a solution for covering exposed substrate edges on cabinets, shelving, and similar panel-based assemblies, so it slots naturally into casework and fixture workflows. Its 3mm thickness suits high-contact front edges on cabinetry and commercial furniture, where a solid-feeling edge is preferred over thin tape. The 1-5/16 inch width supports use on standard furniture and cabinet carcass stock, giving enough overhang to clean up even if panels are slightly out of nominal dimension, which helps maintain visual consistency across a bank of doors or drawers.
The FLEX note in the SAP description signals a flexible construction, which becomes helpful on projects that blend straight cabinet runs with mild curves, allowing the same edgeband type to serve both conditions. The CP10040 identifier ties this reel to a defined Rehau specification, so shops that have dialed in edgebander heat and feed settings for CP10040 material can expect similar handling behavior on this part number, supporting repeatable machine setup and reduced test scrap. With a 300ft roll length, the edgebanding is oriented toward multi-part or multi-cabinet work, allowing production runs to stay on a single color and thickness without frequent roll changes, which supports consistent appearance on larger contracts.
The 3mm PVC thickness on this edge banding gives trimming tools a stable bearing path, which can reduce the tendency for cutters to dig into the face material and helps maintain square, crisp edges in production. Because the banding is defined at 1-5/16 inches wide, operators have predictable overhang for top and bottom trimming, so they can set their trimmers and scrapers once and repeat passes across multiple parts with the same setup. The classification as Edge Banding from Rehau, Inc. indicates it is designed around edging tasks rather than general-profile components, which aligns well with common edgebanding machines and hand tools already in cabinet and millwork shops.
The 300ft designation in the SAP description supports longer continuous runs on automatic edgebanders, which can limit joint locations to planned terminations like cabinet ends instead of mid-run splices. The CP10040 reference in the description also serves as a control point for project documentation, so estimators and shop managers can specify 303334-337 by number and expect the same 1-5/16 inch by 3mm PVC material each time, helping reduce variation between sample pieces and final production work.
The Rehau PVC edgebanding 303334-337 is specified at 1-5/16 inch width and 3mm thickness, which supports trimming to a flush, substantial edge on typical panel-based cabinet components.
The 3mm thickness gives a heavier PVC edge, which provides more material for trimming tools and yields a more robust front edge on doors, drawer fronts, and casework.
The FLEX note in the description indicates a flexible PVC edgebanding, helping it conform to gentle curves or minor panel variations during installation on cabinetry or fixtures.
The 300ft length offers extended continuous feed on edgebanders, reducing roll changes and splice points, which supports consistent appearance across large cabinet or shelving projects.
The CP10040 reference identifies a specific Rehau formulation or line, helping shops standardize on one material family and repeat machine setups and visual results from job to job.
The 1-5/16 inch width provides extra coverage over typical panel thicknesses, giving installers controlled overhang to trim back for a flush, uniform edge across parts.
The Rehau PVC edgebanding 303334-337 combines a 1-5/16 inch width, 3mm thickness, and flexible CP10040 PVC construction in a 300ft roll, so it fits naturally into cabinet and panel-edge workflows that demand repeatable setup and consistent finished edges. For shops planning multi-part runs or matching existing Rehau, Inc. edge banding jobs, this defined part number and dimension set streamlines specifying, cutting lists, and production planning. Put this edge banding into your material list when you want a clearly identified PVC option for covering exposed panel edges on casework and fixtures.
Sold In: 1 Roll