Rehau PVC edgebanding 303334-582 provides a PVC edge banding solution sized at 1-5/16 inches wide and 3mm thick, so it covers standard panel edges while giving them a consistent finished thickness. The flexible design identified as FLX allows the banding to follow gentle curves and minor panel irregularities, which helps reduce edge gaps on cabinets, furniture parts, and shelving. The CP60119 designation, combined with an embossed lacquer description, indicates a textured lacquered surface on the PVC that supports a more furniture-ready appearance straight off the edgebander. A 300ft roll length keeps longer runs or repeat jobs on the same project using one part number, which supports uniform edge appearance across multiple components. This Rehau, Inc. edgebanding is part of the edge banding product class, so it is meant specifically to finish raw board edges in woodworking and casework shops.
The 1-5/16 inch width on this Rehau PVC edge banding gives operators enough coverage to center the tape on common board thicknesses while still allowing clean trimming passes on the edgebander or trimmer. The 3mm thickness works with setups designed for thicker PVC tapes, so machines can be dialed in for a more pronounced edge radius or flush profile as required. The flexible nature referenced by FLX aids feeding through edgebanding machines and around modest curves, which supports smoother tracking and reduces edge tension. The CP60119 embossed lacquer surface also interacts well with typical trimming and scraping steps, helping maintain the textured look after machining. With a 300ft roll, shops can stage fewer roll changes during a run, which supports steadier machine setup for the entire edge sequence.
This Rehau PVC edgebanding, identified as 303334-582 and classified as edge banding, is aimed at woodworking applications where raw panel edges need to be finished to match or complement the face material. The 1-5/16 inch width works well on many cabinet boxes, shelving, and furniture components that use standard sheet goods, giving enough coverage for accurate alignment and final trimming. With its 3mm thickness, this PVC tape suits projects where a more substantial edge is desired, such as higher-use cabinet fronts or exposed shelving, because the thicker edge can visually balance heavier doors and panels. The flexible FLX design helps on runs with modest curves or slightly irregular substrates, so it can be used across a mix of straight parts and mildly contoured pieces within the same job. The 300ft roll length supports both one-off custom projects and small production runs under one consistent Rehau, Inc. part number.
The CP60119 embossed lacquer description signals a textured lacquered surface that gives the PVC banding a more finished furniture-like appearance, reducing extra finishing steps on the edge itself. Because the edgebanding is PVC and 3mm thick, machines tuned for heavier PVC profiles can cut, radius, and scrape the edge to match adjacent faces, which is useful when dialing in consistent visible joints. The flexible FLX characteristic supports better contact between tape and substrate, helping adhesive-bonded edges sit tight along the full length of a part. The 1-5/16 inch width also offers a forgiving margin for slight panel thickness variation, so trimmed edges still present a straight line. With a defined manufacturer part number, 303334-582, repeat orders can match previous jobs, which helps maintain visual continuity when expanding cabinet runs or replacing individual panels in service.
Rehau PVC edgebanding 303334-582 is specified at 1-5/16 inches wide and 3mm thick, so it covers common panel edges and delivers a thicker, more substantial edge profile after trimming.
The flexible FLX design lets this PVC edge banding follow gentle curves and minor panel irregularities, supporting tight edge contact and reducing visible gaps along cabinet or furniture parts.
The CP60119 embossed lacquer surface describes a textured lacquered finish on the PVC, giving the edge a more furniture-ready appearance directly after the edgebanding process.
The 300ft roll length allows longer or repeated runs using the same tape, helping maintain consistent edge color, texture, and setup across multiple cabinets or panels.
The 3mm PVC thickness suits cabinets, furniture, and shelving where a more pronounced edge profile is desired, supporting a heavier-duty look on exposed or frequently handled parts.
The 1-5/16 inch width gives enough overhang for alignment and cleanup while still fitting typical edgebanding and trimming setups used on standard sheet-good thicknesses.
This Rehau PVC edgebanding 303334-582 combines a 1-5/16 inch width, 3mm thickness, flexible FLX design, and CP60119 embossed lacquer surface to support clean, consistent edges across cabinet and furniture projects. The 300ft roll length allows shops to run multiple parts or entire jobs under the same manufacturer part number, helping edges match from the first panel to the last. For woodworking operations that rely on steady throughput and repeatable appearance, adopting this dedicated edge banding class product helps align panel finishing with production demands.
Sold In: 1 Roll