Rehau ABS edgebanding 315608-091 is an ABS edge banding from Rehau, Inc. that finishes exposed panel edges so raw cores are covered and job-ready. The 15/16 inch width matches common panel thickness ranges, so you can trim back to a tight, professional line without starving the face. The 1.2mm thickness gives a substantial edge profile, helping panels feel solid at the touch point where hands repeatedly land. The ABS material creates a defined transition between surface and edge, supporting consistent visual alignment across multiple cabinets or fixtures. This edgebanding is identified as LE CP20994 EMB LAC, tying the banding to a specific decorative program so finished edges track with the intended look. The 600ft length keeps longer runs or multiple units under the same part number, which reduces mid-project lot changes and helps keep assemblies visually consistent.
The 15/16 inch width on this Rehau ABS edgebanding leaves margin beyond typical panel thickness, giving trimmers enough material to work against while dialing in a flush, chip-free edge. The 1.2mm thickness balances profile and workability, so the banding presents a noticeable edge without overwhelming smaller components. Because this product is classified as edge banding, it is intended to be applied along exposed panel sides, allowing you to treat every visible edge to the same finished specification. The LE CP20994 EMB LAC identification keeps the edge visually tied to a defined program, so each cut length on a run behaves as part of a single, consistent system.
This Rehau ABS edgebanding, identified as 315608-091, fits into woodworking projects where exposed panel edges need a finished treatment that matches a defined program. The 15/16 inch width aligns with edge finishing on panels built to common thickness standards, so casework sides, shelves, and door blanks can all take the same band size. With a 1.2mm thickness, the banding suits fronts and vertical surfaces where a slightly thicker edge profile is desired, such as cabinetry faces or storage partitions in commercial or residential spaces. The LE CP20994 EMB LAC designation connects the edge to a specific decor intent, allowing fabricators to keep the edge choice consistent whenever that program is used. Over a 600ft length, the product supports multi-unit jobs, so banks of cabinets, long runs of shelving, or matching fixtures can all carry the same edge reference from start to finish.
The ABS material in this edge banding defines how the edge interacts with the workpiece, giving a stable synthetic surface that maintains its profile as pieces are handled and aligned during assembly. The 15/16 inch width factors directly into trimming workflows, providing enough banding beyond the panel edge so tool passes can be set for clean cuts without risking exposure of the core. At 1.2mm thick, the banding supplies a measurable edge that remains visible and tactile across repeated doors and panels, which helps installers visually align reveals and maintain even sight lines along a run. The LE CP20994 EMB LAC identifier links each cut segment back to one defined reference, so replacement fronts or added units use the same edge part number for continuity. The 600ft length keeps that reference active across larger batches, supporting repeatable results from layout through final installation when the same program is specified on future work.
Rehau 315608-091 is ABS edge banding, so it is used to finish exposed panel edges and cover raw substrate on cabinetry, fixtures, or other panel-based assemblies.
This Rehau ABS edgebanding is 15/16 inch wide, giving coverage beyond typical panel thickness so edges can be trimmed flush while keeping the substrate fully concealed.
The 1.2mm thickness provides a defined edge profile, which helps doors, drawer fronts, and panel edges feel substantial and look consistent across a run.
The 600ft length supports longer production runs, so multiple cabinets or fixtures can be edged from the same part number for consistent appearance across the job.
LE CP20994 EMB LAC identifies a specific decor reference, tying this ABS edge banding to a defined visual program for coordinated surface and edge selection.
This ABS edge banding is manufactured by Rehau, Inc., aligning it with Rehau edgebanding systems used across many woodworking and cabinet projects.
The Rehau ABS edgebanding 315608-091 combines a 15/16 inch width, 1.2mm thickness, and LE CP20994 EMB LAC reference to support consistent edge finishes on panel-based work. The 600ft length keeps that specification available across multi-unit runs and follow-up pieces. Selecting this ABS edge banding for projects built around the same decor reference lets shops and installers maintain a single, known edge detail from initial install through later additions, keeping surfaces and edges visually aligned.
Sold In: 1 Roll