
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
J95-DP2 spacer for J95 hinge is a gray adjustment plate designed for the Sugatsune J95 concealed hinge and the J160 soft-close hinge. This spacer changes door position by 5/64 inch (2 mm), which gives you a simple, repeatable way to fine-tune overlays and clearances on cabinet doors using these hinge series in the shop or on site.
The spacer decreases overlay of outset doors by 5/64 inch (2 mm), so an outset door can be pulled back slightly toward the cabinet face for better alignment with adjoining fronts or trim. The same part increases clearance of inset doors by 5/64 inch (2 mm), helping an inset door clear the cabinet face more consistently in tight reveals.
The spacer can be doubled for a 5/32 inch (4 mm) thickness, which lets you apply a 2 mm or 4 mm change using the same part number, depending on the door condition. It requires a countersunk self tapping screw 5 x 25 for mounting, so the screw head seats properly and the spacer sits flat under the hinge in the hinge stack.
This J95-DP2 spacer works as part of the hinge stack for the J95 concealed hinge and the J160 soft-close hinge, so it mounts where the hinge body meets the cabinet or mounting surface. The specified 5/64 inch (2 mm) correction is built into the spacer thickness, giving you a predictable change with each piece.
When decreasing overlay on an outset door by 5/64 inch (2 mm), the spacer shifts the hinge relationship to the cabinet, which pulls the door edge back so it does not project as far past the cabinet face. For inset doors, the same spacer increases clearance by 5/64 inch (2 mm), moving the door relative to the opening so it has more room to swing inside a framed or frameless cabinet.
Doubling the spacer to reach 5/32 inch (4 mm) thickness applies the same concept with a larger adjustment, letting you correct overlays or clearances that are off by roughly 4 mm using two of the same J95-DP2 spacers in the hinge stack for that location.
The J95-DP2 spacer is specified for the J95 concealed hinge and the J160 soft-close hinge, which positions it directly in installations using these Sugatsune hinge families on cabinets, casework, or similar door projects. Because it decreases overlay of outset doors by 5/64 inch (2 mm), it fits situations where a door sits too far past the cabinet front and needs to be brought closer to surrounding surfaces for a cleaner line.
In the same way, its ability to increase clearance of inset doors by 5/64 inch (2 mm) addresses layouts where an inset door edge is close to the cabinet face and benefits from a small, controlled shift. This makes the spacer useful anywhere J95 or J160 hinges are used with inset doors that must swing freely inside an opening while maintaining a narrow reveal.
The gray color and specific J95-DP2 designation help distinguish this spacer from other hinge components, so it can be stocked with J95 concealed hinges and J160 soft-close hinges as part of the standard setup for these hinge lines in a cabinet shop or installation van.
The defined 5/64 inch (2 mm) change from the J95-DP2 spacer means each spacer adds a known offset to the hinge position, which supports repeatable results across multiple doors in a bank of cabinets. When small overlay differences appear from door to door, this fixed value lets you correct them in a controlled way instead of relying only on hinge arm adjustments.
For projects needing a larger correction, the option to double the spacer for a 5/32 inch (4 mm) thickness gives you a second, predictable adjustment step. Using two spacers to reach 4 mm of change helps bring badly misaligned overlays or tight inset clearances back into an acceptable range without changing the hinge model or drilling new hinge cups.
The requirement for a countersunk self tapping screw 5 x 25 means the fastener head nests into the spacer body during mounting, which keeps the spacer and hinge in tight contact. That solid interface supports the door weight through the hinge stack and reduces the chance of unwanted movement at the connection point over time.
The J95-DP2 spacer is for the J95 concealed hinge and the J160 soft-close hinge, so it serves adjustments specifically on these Sugatsune hinge series in cabinet installations.
The J95-DP2 spacer changes door position by 5/64 inch, or 2 mm, providing a defined adjustment for decreasing outset door overlay or increasing inset door clearance.
The J95-DP2 spacer can be doubled to reach a 5/32 inch, or 4 mm, thickness, giving you a larger correction using the same spacer in a stacked configuration.
On outset doors, the J95-DP2 spacer decreases overlay by 5/64 inch, or 2 mm, which pulls the door closer to the cabinet front for more consistent projection.
On inset doors, the J95-DP2 spacer increases clearance by 5/64 inch, or 2 mm, allowing the door edge more room relative to the cabinet face during opening.
The J95-DP2 spacer requires a countersunk self tapping screw 5 x 25, so the screw head sits flush and supports a solid interface in the hinge stack.
The J95-DP2 spacer for J95 hinge gives you a defined 5/64 inch (2 mm) adjustment for J95 concealed hinges and J160 soft-close hinges, with the option to double to 5/32 inch (4 mm) when more correction is needed. Its role in decreasing overlay of outset doors or increasing clearance of inset doors ties directly into clean door reveals and consistent swing on cabinets using these hinge systems. For cabinet, casework, or similar projects built around Sugatsune J95 and J160 hinges, this gray spacer provides a repeatable way to dial in overlay and clearance to match design intent and job requirements.