Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Emtek Modern Rectangular Warwick appliance pull is built as a glass shower door back to back handle, so it provides a solid gripping point on both sides of the glass during everyday use. The 18 inch Center to Center layout spaces the mounting points widely, which helps distribute hand force along the glass and supports comfortable operation on taller doors. Its satin brass finish gives a consistent warm tone, so it visually ties into other satin brass bathroom hardware in the same space. The modern rectangular profile keeps the sightline clean, which suits contemporary and transitional glass enclosures. Because this pull is designed specifically for glass shower doors, its details are focused on clamping through glass rather than wood, which matters when planning hardware on frameless or semi-frameless panels.
This Modern Rectangular Warwick appliance pull is specified to fit glass door thickness between 1/4 inch and 1/2 inch only, so its through-glass clamping range is tailored to common shower door glass sizes. That thickness window helps the hardware seat properly on the glass, supporting a secure clamp when the fasteners are tightened. The pull uses a back to back arrangement, where one grip tightens against the other through the glass, which creates a balanced load on both faces of the panel. The 18 inch Center to Center spacing also sets where holes in the glass must be located, so it directly guides door fabrication and layout.
The Emtek Modern Rectangular Warwick appliance pull is crafted for glass shower doors, so it is suited to frameless or framed glass panels within the specified thickness range of 1/4 inch to 1/2 inch. Its back to back design means both the exterior and interior sides of the shower door gain a matching grip, which is useful on swinging doors that open both in and out of the enclosure. The 18 inch Center to Center size makes the pull a good fit for taller glass doors where users benefit from a longer handhold. Because the pull is finished in satin brass, it aligns visually with satin brass fittings around the shower area, which supports a consistent look across hinges, controls, and decorative hardware.
This Warwick appliance pull uses a defined 18 inch Center to Center dimension, which gives installers an exact measurement to transfer when drilling or lining up pre-bored glass. That fixed spacing helps keep the pull level and centered relative to door edges, reducing rework due to misaligned holes. The modern rectangular form provides straight edges along the pull, which can be sighted against the door top or vertical stile to fine tune alignment visually during tightening. Its back to back configuration clamps the glass between the two grips, which distributes clamping force across both sides of the panel instead of concentrating it on one face. The satin brass finish is applied to present a consistent surface appearance, so minor adjustments in position do not reveal mismatched areas during final alignment. Because the pull is defined for glass door thickness between 1/4 inch and 1/2 inch only, the clamping components are proportioned to engage properly within that range, supporting repeatable installation results on qualifying glass panels.
The Emtek Modern Rectangular Warwick appliance pull is crafted for glass shower doors, so its through-glass configuration matches common shower door construction.
The Emtek Modern Rectangular Warwick appliance pull has an 18 inch Center to Center dimension, which sets the required hole spacing in the glass door.
The Emtek Warwick appliance pull fits glass door thickness between 1/4 inch and 1/2 inch only, so it clamps properly on glass within that range.
The Emtek glass shower door back to back pull uses two grips that tighten against each other through the glass, giving a handle on both sides.
The Emtek Modern Rectangular Warwick appliance pull is finished in satin brass, so it coordinates with other satin brass bath and shower hardware.
The manufacturer part number for the Emtek Modern Rectangular Warwick appliance pull in satin brass is GBTB86712US4, which identifies this specific configuration.
The Emtek Modern Rectangular Warwick appliance pull in satin brass brings an 18 inch Center to Center, back to back configuration dedicated to glass shower doors, which supports both secure gripping and consistent alignment. Its defined fit for glass door thickness between 1/4 inch and 1/2 inch focuses its use on common shower door glass sizes, which simplifies planning around that range. With its modern rectangular profile and satin brass finish, this pull pairs visual consistency with clear installation dimensions, giving installers and project planners a straightforward choice for matching glass shower openings to a known Emtek part number.