Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Emtek Transitional Heritage Blythe appliance pull gives a glass shower door a defined grip point, so users operate the door with control instead of handling the glass edge. This Emtek Transitional Heritage Blythe appliance pull is crafted for glass shower doors, so its proportions suit full-height panels rather than small cabinet faces. The 12-inch Center to Center layout spreads hand pressure along more glass, which helps door operation feel solid and controlled. Its back-to-back appliance pull configuration provides a grip on both sides of the door, so opening and closing feel the same from the shower side or the room side. The Satin Brass finish delivers a warm metallic surface, so the handle visually coordinates with other brass plumbing or decorative hardware in the bathroom.
This pull fits glass door thickness between 1/4 inch and 1/2 inch only, so installers can match it to doors within that thickness range for proper clamping and thread engagement. The grip with #10-32 threads in the stem works as the fastening side, so it draws the assembly tight when the screws engage those threads. The mating grip with a 3/8 inch diameter hole in the stem accepts the bevel head screws through the glass, so the hardware stacks cleanly without oversized projections. This combination of threaded stem and mating hole helps the pull seat firmly against the glass surfaces.
This glass shower door handle uses a back-to-back appliance pull layout, so one grip mounts on the exterior and one on the interior of the glass panel. The 12-inch Center to Center spacing sets the distance between these two stem locations, so drilling points can be laid out consistently across multiple doors in a project. The stem on one grip is threaded for #10-32 fasteners, so the fastening side captures the bevel head screws coming through from the opposite grip. The other grip has a 3/8 inch diameter hole in the stem, so the screws pass through freely and seat their bevel heads where they contact the stem. This arrangement creates a clamping action on the glass, so the pull feels solid during repeated opening and closing.
The two 3/8 inch diameter bevel head screws with #10-32 threads by 3/4 inch long and the two 3/8 inch diameter bevel head screws with #10-32 threads by 7/8 inch long give length options, so installers can use screw lengths that suit glass thickness within the 1/4 inch to 1/2 inch fit range. Using screws sized to the panel thickness helps the threaded stem engage properly without excessive projection, which supports a stable, flush-feeling installation on the door surface. The set of gaskets sits between the grip components and the glass, so the metal stems and grips bear on a gasket layer instead of directly on the glass edge area. This gasket interface helps distribute contact pressure around the mounting holes, so the clamping force from the back-to-back appliance pull is applied more evenly across the glass during regular door operation.
The Emtek Transitional Heritage Blythe appliance pull is crafted for glass shower doors, so it suits installations where the handle mounts directly through a glass panel.
The Emtek Transitional Heritage Blythe appliance pull fits glass door thickness between 1/4 inch and 1/2 inch only, so it targets common shower glass dimensions within that range.
This glass shower door handle has a 12-inch Center to Center dimension, so the mounting holes on the glass are spaced 12 inches apart for a long, full-hand grip.
The Emtek glass shower door pull is finished in Satin Brass, so it presents a warm metallic tone that coordinates with brass bathroom fixtures.
The back-to-back appliance pull design places one grip on each side of the glass, so the two grips clamp together through the panel to form a single operating handle.
Part number GBTB86910US4 identifies this specific Transitional Heritage Blythe 12-inch Satin Brass back-to-back appliance pull, so projects can reference the exact model when reordering.
The Emtek Transitional Heritage Blythe appliance pull, part number GBTB86910US4, gives glass shower doors a 12-inch Center to Center back-to-back handle sized for 1/4 inch to 1/2 inch glass. The Satin Brass finish and glass-focused construction align well with shower applications where a substantial, two-sided grip is preferred. For glass shower projects built around brass-toned fixtures and through-glass hardware, this Emtek glass shower door pull offers a defined specification to integrate into the door layout and drilling plan.