Schaub Sabre Edge Pull 5 CC Polished Nickel is a decorative handle from Schaub and Company that grips on the cabinet edge, so it operates the door or drawer without a projecting traditional pull. The polished nickel finish provides a bright metallic surface, which gives cabinets a crisp, finished look in modern or transitional jobs. The 5 inch center-to-center mounting layout defines the hole spacing, which keeps drilling consistent across a run of fronts. Overall length of 6-1/4 inch gives more hand contact area than the mounting span, which helps users grab the pull comfortably in regular use. Placement in the Decorative Hardware & Moldings category as Handles and Pulls signals that this part is intended as visible working hardware, so it can be specified confidently on face frames or frameless projects where appearance matters.
The specified 5 inch center-to-center spacing on this edge pull defines where the mounting holes fall, so jigs or drill guides can be set once and reused across all fronts in the job. The overall 6-1/4 inch length means the pull extends beyond those holes, which helps conceal minor drilling shifts and maintains a straight visual line along the cabinet edge. The thread and screw size of #8 x 5/8 inch flat head sheet metal screw describes the screw interface, so the pull seats flush when the flat heads draw tight into the countersunk areas. That screw sizing also suits typical cabinet door and drawer front thicknesses where a 5/8 inch fastener can bite securely without excessive projection through the back face.
The 5 inch center-to-center layout positions this edge pull well on cabinet doors and drawers that can accept two mounting points close to the working edge, which supports smooth opening with a fingertip grip. Its polished nickel finish ties into polished nickel cabinet edge pull projects, so it can run across kitchens, baths, or built-ins where a uniform metal tone is specified. The 6-1/4 inch overall length allows the pull to span a noticeable section of the door or drawer edge, which helps it read as a deliberate design element rather than a tiny tab. As a part of Decorative Hardware & Moldings in the Handles and Pulls class, it is suited to visible cabinet faces, so it can be used confidently on upper, base, or tall units that sit at eye level.
The defined 5 inch center-to-center screw spacing gives installers a reliable measurement for story poles or drilling jigs, which cuts down layout time when outfitting long cabinet runs. Because the pull length is 6-1/4 inch, there is some forgiveness if drilling lands slightly off center, as the body still bridges the span and keeps the edge sightline clean. The use of #8 x 5/8 inch flat head sheet metal screws means the fasteners sit flush within the countersunk mounting points, so the pull bears evenly against the cabinet surface without rocking. That same screw length works practically with many standard cabinet door and drawer front thicknesses, creating a solid hold while keeping the interior face straightforward to finish around. The clear Manufacturer Part 10012-PN tied to Schaub and Company supports future service work, because the exact same edge pull can be ordered again when adding cabinets or replacing hardware years later.
The Schaub Sabre edge pull has a 5 inch center-to-center dimension, which sets the distance between mounting holes for consistent drilling on cabinet doors and drawers.
The edge pull has a 6-1/4 inch overall length, which gives extra gripping surface beyond the mounting span for easier hand contact during everyday cabinet use.
The 10012-PN edge pull is finished in polished nickel, which provides a bright metallic look that pairs with other polished nickel decorative hardware on the project.
This edge pull specifies #8 x 5/8 inch flat head sheet metal screws, which seat into the pull and grip typical cabinet door or drawer front thicknesses securely.
This Sabre edge pull is manufactured by Schaub and Company, which helps match this model across projects using the same decorative hardware line.
The part number 10012-PN identifies this specific polished nickel Sabre edge pull, which simplifies specifying, ordering, and matching replacements by exact model.
The Schaub Sabre edge pull, part 10012-PN, combines a 5 inch center-to-center layout with a 6-1/4 inch overall length, so cabinet hardware spacing and sightlines stay consistent across the job. Its polished nickel finish delivers a unified metal tone that coordinates with other polished nickel components. With the specified #8 x 5/8 inch flat head sheet metal screw interface, the pull seats firmly against typical cabinet surfaces. For projects calling for a polished nickel edge pull with defined mounting dimensions, this model offers a clearly documented option for detailed cabinet work.