Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Schaub Baker edge pull 4 CC is a cabinet handle designed as an edge pull in unlacquered brass, so it mounts at the door or drawer edge and presents a low-profile grip that suits straightforward cabinet layouts. The 4 inch center-to-center dimension fixes the mounting hole spacing, which helps plan drilling and layout across multiple fronts for consistent alignment. The overall 5-1/4 inch length gives extra finger contact area beyond the mounting span, supporting a solid grip on wider drawers or doors. The handle is built around an edge pull form, which positions the user grip along the door or drawer edge to keep the face panel visually clear. The unlacquered brass material keeps the metal surface bare, so it can develop a natural patina during regular use in a working shop or residential environment.
This edge pull uses #8 x 5/8 inch flat head sheet metal screw fasteners, which set a defined screw gauge and length for mounting into the cabinet substrate. The flat head profile is intended to seat flush in a countersunk mounting point on the pull, supporting firm contact between pull and door or drawer material. The specified sheet metal screw pattern is suited to biting into the cabinet construction material, so the pull can resist everyday opening and closing loads. With the 4 inch center-to-center spacing fixed, installers can lay out two mounting holes for these screws on an accurate line along the edge, which helps maintain straight visual alignment across multiple fronts.
This Schaub Baker edge pull, identified as 10021-UNBR, belongs to the handles and pulls class within decorative hardware and moldings, positioning it for cabinet and casework use where an edge-mounted grip is preferred. The 4 inch center-to-center dimension suits installations on standard cabinet doors or drawers that have enough width at the edge to accept that span without crowding other hardware. The 5-1/4 inch overall length offers balanced proportions on medium-size doors and drawers, so the pull does not appear undersized against typical kitchen or shop fronts. As an unlacquered brass edge pull, it can be used in layouts that rely on warm metal tones which can age as the brass surface reacts over time. Within a run of cabinets, repeating this same Schaub edge pull across doors and drawers creates a consistent visual line at the edges, because every pull shares the same length and mounting spacing.
The defined 4 inch center-to-center spacing on this edge pull supports accurate drilling templates, which can be reused across many doors and drawers to keep the pulls lined up from cabinet to cabinet. By using the same #8 x 5/8 inch flat head sheet metal screw on each pull, the fastening method stays uniform, which simplifies edge preparation and helps maintain similar holding strength at every opening. The flat head design allows the screw heads to sit within the pull body, which helps transfer pull forces flat against the cabinet surface. Because the overall length is fixed at 5-1/4 inches, installers can reference the ends of the pull relative to the door or drawer edge to visually balance the hardware on the panel. Working with a single defined part, Schaub 10021-UNBR, avoids mixing dimensions or finishes, which contributes to consistent sightlines and predictable hardware behavior throughout the installation.
This edge pull has a 4 inch center-to-center dimension, so drilling layouts can be based on that fixed spacing for repeatable cabinet hardware placement.
The Schaub 10021-UNBR edge pull has a 5-1/4 inch overall length, which provides added gripping area beyond the 4 inch mounting span.
This Baker edge pull is specified as unlacquered brass, so the brass surface remains bare and can develop a natural patina through regular service.
This edge pull is described with a #8 x 5/8 inch flat head sheet metal screw, setting a defined screw gauge and length for mounting.
This product is categorized under decorative hardware handles and pulls, aligning it with cabinet doors and drawers that use an edge-mounted grip.
This pull is identified by the Schaub and Company manufacturer part number 10021-UNBR, which specifies this exact unlacquered brass edge pull.
The Schaub Baker edge pull 4 CC combines an edge-mounted form, 4 inch center-to-center spacing, and 5-1/4 inch overall length to support consistent cabinet hardware layouts. The unlacquered brass construction provides a bare brass surface that can age as the project sees use. With a defined #8 x 5/8 inch flat head sheet metal screw interface, mounting can follow a clear screw pattern across doors and drawers. For projects calling for an edge pull with these exact dimensions and unlacquered brass material, this Schaub 10021-UNBR model offers a clearly specified option.