Schaub Northport pull 3-1/2 inch identifies this handle as a Northport series pull from Schaub and Company with a 3-1/2 inch center-to-center layout, which sets up a dependable mounting pattern for cabinet doors or drawers that match this drilling spread. The pull has round bases at each end, so the contact area against the cabinet surface is broad, which helps distribute hand force and operating loads over a wider area during daily use. Its satin nickel finish defines the surface look as a muted metal tone, which keeps glare down under task lighting while giving a consistent appearance across multiple handles in the same run. The product sits in the decorative hardware and moldings handles and pulls category, so it is built to function as a primary gripping point on cabinet fronts where a dedicated handle is preferred over finger pulls.
The 3-1/2 inch center-to-center measurement on this Schaub Northport pull sets a fixed spacing between the two fastener points, which streamlines layout for installers who drill through the cabinet face from the back side. The pull uses a thread or screw size of #8-32, which defines the thread standard that engages into the pull, allowing hardware that matches this thread to draw the handle tight against the surface. With round bases at each end, the pull presents a specific bearing area around each fastener point, which can help the handle seat evenly against flat door and drawer faces when tightened. The satin nickel finish applied to the pull establishes a stable surface appearance around these mounting areas, which supports a uniform look even where tools contact near the bases during installation.
The Schaub Northport pull with round bases is defined as a handle and pull within decorative hardware and moldings, so its primary role is to serve as a gripping point on cabinet doors and drawers. The 3-1/2 inch center-to-center layout on this pull makes it suitable for fronts drilled on that spread, which allows doors and drawers in the same run to share a consistent handle position and spacing. Because the pull uses round bases, each end sets down on the cabinet face as a circular contact pad, which can visually anchor the handle on rail-and-stile doors or framed drawer fronts. Those round bases also create a clear edge where paint, stain, or laminate meets the hardware, which is useful when aligning multiple pulls against a repeating cabinet pattern. As a satin nickel piece, the pull presents a specific finish that can be coordinated with other satin nickel decorative hardware in the same kitchen, bath, or built-in project so the hardware line reads as intentional rather than patched together from different looks.
The 3-1/2 inch center-to-center measurement on this Northport pull is a key layout dimension, because it defines exactly where through-holes must land in the cabinet face to bring the posts into alignment, which helps avoid rework from mis-drilled fronts. Using a #8-32 thread or screw size at the connection point means the pull engages with a defined machine-thread standard, which helps the handle draw down squarely as the screws tighten from the back side. The round bases at each end act as integrated escutcheons, so they create a finished edge around each mounting point, which can help hide small drilling tear-out or layout pencil marks once the handle is in place. With its satin nickel finish, the pull keeps a consistent appearance across all visible surfaces, so when several units are mounted in a row the line of hardware reads clean and uniform from any normal viewing angle.
The Schaub Northport pull has a 3-1/2 inch center-to-center dimension, which sets the spacing between mounting holes and guides drilling or replacement on cabinet fronts using that layout.
This Northport pull uses a thread size of #8-32, which identifies the machine-thread standard that engages into the pull posts to secure it against doors or drawers.
The pull has a satin nickel finish, which gives it a muted metallic look that coordinates with other satin nickel decorative hardware in the same installation.
The round bases create a defined contact area at each end of the pull, which helps the handle seat neatly on the surface and visually frames the mounting points on the cabinet front.
This product is a handle and pull in the decorative hardware and moldings category, so it functions as a primary grip on cabinet doors or drawers.
This satin nickel Northport pull is manufactured by Schaub and Company, which identifies the decorative hardware line for coordinating matching pulls within a project.
This Schaub Northport pull with round bases, 3-1/2 inch center-to-center, and satin nickel finish offers a defined layout, known thread size, and consistent appearance, which helps cabinet shops and serious DIY users plan clean, repeatable hardware runs on doors and drawers.