Schaub Northport pull gives cabinets a defined grip point by providing a solid handle across the drawer or door front, which supports consistent opening and closing on frequently used casework. The Northport pull with round bases spreads contact across the mounting area, which helps distribute force where the handle meets the cabinet surface during daily use. Its brushed bronze finish presents a bronze-colored surface with a brushed appearance, which offers a specific look that can align with other bronze-tone hardware on the job. This pull is identified as Schaub and Company part number 212-BBZ, which helps match this exact model across drawings, bids, and repeat orders. As a handle and pull in the Decorative Hardware & Moldings category, it serves as a visible touchpoint on finished cabinetry, so the chosen style affects the final appearance of the installation.
The 5 inch center-to-center measurement on this Schaub Northport pull defines exactly where to drill through the cabinet front, which simplifies layout when repeating the same pattern across multiple doors and drawers. Because the pull uses a #8-32 thread size, it pairs with #8-32 threaded fasteners passing from the rear of the cabinet face into the pull's posts, which creates a positive mechanical connection through the panel. As a handle and pull with round bases, each base sits flat on the exterior surface, which helps align the pull as it is tightened so the handle sits straight and parallel to the cabinet edge.
This Schaub Northport pull with round bases, part number 212-BBZ, is positioned for use on cabinet doors and drawers where a 5 inch center-to-center handle is called out on the design. Its role as a handle and pull in the Decorative Hardware & Moldings category means it is intended for visible locations on finished woodworking, so it becomes part of the overall elevation when cabinets are viewed straight on. The brushed bronze finish provides a specific color tone that can align with bronze-finished hinges, knobs, or other decorative hardware when a project calls for a coordinated appearance. Because the center-to-center dimension is fixed at 5 inches, it matches layouts that are already drilled or planned around that spacing, which supports consistent sizing across a kitchen, vanity, or casework run.
The round bases at each end of the pull establish defined bearing surfaces on the cabinet face, which helps position the handle relative to stile or rail edges when aligning multiple pulls in a row. As a product from Schaub and Company, this pull sits within the broader Schaub handles and pulls family, which lets a project use this specific style wherever a 5 inch center-to-center handle is specified. The dedicated part number 212-BBZ identifies this exact brushed bronze version, which helps avoid mix-ups with other finishes or sizes when ordering for a job where hardware details are tied directly to project documentation.
The clearly stated 5 inch center-to-center spacing on this Northport pull sets a fixed distance between mounting points, which allows installers to use jigs, templates, or consistent measurements to reproduce the same hole pattern across multiple fronts. Using a #8-32 thread size standardizes the fastener interface, which streamlines installation when a shop or field crew is already set up around #8-32 threaded connection points for pulls.
The round bases on the pull define circular contact areas where the handle meets the cabinet surface, which can aid in keeping the pull square to door and drawer edges during tightening so handles line up visually from cabinet to cabinet. Because the finish is described as brushed bronze, it delivers a consistent finish statement job-wide when this model is specified wherever this color and texture are desired. In practice, combining the defined center-to-center dimension, the standard thread size, and the round base geometry supports repeatable placement, straightforward fastening, and uniform appearance over the entire run of cabinets.
The Schaub Northport pull uses a 5 inch center-to-center dimension, which sets the spacing between mounting holes and guides drilling layout across cabinet doors and drawers.
The 212-BBZ Northport pull uses a #8-32 thread size, which lets installers pair it with #8-32 threaded fasteners for secure attachment through cabinet fronts.
This Schaub and Company pull has a brushed bronze finish, which provides a bronze-toned, brushed surface that coordinates with other bronze decorative hardware on a project.
The Northport pull functions as a handle on cabinet doors and drawers, providing a fixed grip point so users can open and close casework consistently.
The 5 inch center-to-center measurement defines exact hole spacing, which supports uniform pull placement and simplifies using drilling jigs across multiple cabinet fronts.
The Northport pull with round bases spreads contact at each mounting point, which helps align the handle on the cabinet face during fastening.
The Schaub Northport pull with round bases, 5 inch center-to-center, brushed bronze, part number 212-BBZ, combines a defined 5 inch mounting spread with a #8-32 thread interface, which streamlines cabinet drilling and fastening. Its role as a decorative handle and pull in the Decorative Hardware & Moldings category means it serves as both a working grip and a visible design element. For projects built around a 5 inch center-to-center pattern in a brushed bronze finish, this model offers a clearly identified option that can be specified and repeated wherever that spacing and look are required.