Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Schaub Northport pull is a decorative handle from Schaub and Company that serves as a functional grip point on cabinet doors or drawers, giving installers a defined place to open and close fronts on completed casework. The pull sits in the Handles and Pulls product class within Decorative Hardware & Moldings, so it fits naturally into millwork and cabinetry layouts where a consistent hardware style is needed across multiple faces. The Northport design uses square bases, which create clean, defined contact points against the cabinet surface and help present straight visual lines when aligned with door rails or drawer fronts. A satin nickel finish gives the pull a neutral, project-friendly appearance that blends with many hinge and appliance finishes, supporting consistent visual coordination on full-room installations. The product is identified by Manufacturer Part # 216-15, which aids repeat ordering when matching hardware across multiple jobs or phases.
The 5 inch center-to-center measurement on this pull sets the exact spacing between the two mounting points, so drilling operations can follow that dimension to keep handles level and consistent across multiple fronts. With square bases at each end, the installer gains clear visual reference edges when aligning the pull to door rails or drawer fronts, supporting accurate positioning by eye or with layout lines. The specified thread or screw size of #8-32 defines the mating fastener thread, so hardware selection for mounting can target that size for proper fit inside the pull. Being a Schaub and Company pull in satin nickel keeps this piece aligned with decorative cabinet hardware standards, allowing it to plug into existing layout templates and typical cabinet construction workflows.
This Northport pull with square bases belongs to the Decorative Hardware & Moldings category, positioning it for use on cabinet doors, drawers, and similar millwork where a defined pull point is needed. As part of the Handles and Pulls product class from Schaub and Company, it functions as the hand grip element in a typical cabinet hardware set, complementing hinges and interior fittings already present in the casework. The satin nickel finish allows the pull to sit comfortably in residential or commercial cabinetry where neutral metal tones are specified, so it works across kitchens, baths, and built-in storage using similar finish schemes. With a 5 inch center-to-center dimension, this pull is suited to layouts that call for that specific hole spacing, aligning with drilling jigs and design standards that use this size throughout a run of doors or drawer fronts.
The clearly defined 5 inch center-to-center spacing on this pull supports repeatable installation because every drilling operation can follow the same fixed dimension, reducing layout variation from one cabinet front to the next. Square bases at each end give fitters straight edges to reference against door or drawer geometry, helping them maintain parallel alignment with top or side rails and reducing the need for rework due to visible skew. The specified #8-32 thread or screw size creates a consistent fastening interface inside the pull, which helps when replacing an existing handle that uses the same thread or when standardizing on a single fastener type across a project. Identification by Manufacturer Part # 216-15 and the Schaub Northport name simplifies ordering the same pull again for add-on cabinets or service work, supporting long-term visual consistency across phased installations.
The Schaub Northport pull is a decorative handle in the Handles and Pulls class, so it serves as the gripping point on cabinet doors or drawers in woodworking and millwork projects.
The 5 inch center-to-center dimension indicates the distance between the pull's two mounting holes, guiding drilling layouts so handles line up consistently across multiple fronts.
The square bases provide flat, squared contact points that align with cabinet rails or edges, helping installers position the pull straight and flush on doors and drawers.
The pull has a satin nickel finish, which delivers a neutral metallic look that coordinates with many cabinet hinges, faucets, and other visible hardware in a project.
This Northport pull is specified with thread or screw size #8-32, so it mates with standard fasteners using that machine thread in cabinet installations.
The Manufacturer Part # 216-15 uniquely identifies this pull, making it straightforward to reorder the same model for additional cabinets or phased millwork work.
This Schaub Northport pull with square bases, 5 inch center-to-center dimension, and satin nickel finish gives cabinet builders a defined, repeatable hardware choice for doors and drawers. The #8-32 thread specification and Handles and Pulls product class align the pull with common cabinet construction practices, so it drops into woodworking workflows that already rely on standard drilling patterns and fasteners. For projects where the 216-15 part number, satin nickel tone, and 5 inch mounting spread match the design intent, this pull can be specified confidently across new installations or extensions of existing Schaub and Company hardware runs.