Schaub Haniburton pull 5 inch CC describes a decorative handle from Schaub and Company that is built for cabinets and casework where a 5 inch center-to-center layout is already drilled or planned. The 5 inch center-to-center spacing sets the hole pattern, so it lines up with standard 5 inch drilling on doors or drawers. The polished nickel finish defines the visual look, giving a bright, metal surface that reads clean and consistent across a run of cabinets. The handle format puts a solid grip point on doors or drawers, which helps when heavier faces or loaded drawers need a firm pull. Being part of the decorative hardware and moldings range keeps this pull in line with other handles and pulls when a project needs coordinated hardware from the same design family.
The 5 inch center-to-center mounting layout defines exactly where the two fastening points land, which simplifies drilling jigs and speeds repeat drilling across a bank of doors or drawers. Using a pull designed around #8-32 thread or screw size means the internal pull threads match common cabinet machine screws, helping the handle seat firmly against the face material. The polished nickel surface extends across the pull body, so visible hardware on the front of the cabinet reads as a single, consistent finish. As a handle and pull in the decorative hardware range, this part is sized and shaped for hand grip, which supports comfortable operation on frequently used doors and drawers.
The Schaub Haniburton Pull, 5 inch CC, Polished Nickel - 475-PN is defined by its 5 inch center-to-center layout, so it works where two straight-line holes at that spacing are provided in the door or drawer front. That fixed spacing makes it practical on new cabinet runs where drilling patterns can be standardized, and on replacements where existing 5 inch holes are already present. As a handle and pull in the decorative hardware and moldings category, it fills the role of the primary touch point on front faces, so every opening cycle goes through this component. The polished nickel finish places a smooth metal surface under hand contact, which supports a clean feel during daily use. Located on doors or drawers, this pull gives a single, predictable grip location, which helps with consistent operation along a full run of cabinets.
The specified 5 inch center-to-center dimension on the Haniburton model 475-PN lets installers build or use drilling jigs that repeat the same spacing, which reduces layout variation from cabinet to cabinet. When each pull shares this fixed pattern, alignment lines stay straight across drawer stacks and door rows. The #8-32 thread or screw size means the pull body accepts standard #8-32 machine screw threads at each mounting point, which allows the fastener to pull the handle tightly against the face material and resist loosening under normal operation. As a Schaub and Company handle and pull, this part sits inside a coordinated decorative hardware line, which supports predictable aesthetics and dimensions across multiple pieces on the same project. The polished nickel finish runs over the exposed surfaces, so edges, grip area, and mounting posts all present the same tone when lined up along a cabinet bank.
The Schaub Haniburton pull uses a 5 inch center-to-center layout, so the two mounting holes are drilled 5 inches apart, which standardizes spacing across cabinet doors and drawers.
The polished nickel finish provides a bright, reflective metal surface, which helps this pull visually coordinate with other polished nickel hardware and fixtures in the same space.
The pull uses #8-32 thread or screw size at its mounting points, so it mates with standard #8-32 machine screws commonly used in cabinet construction.
This product is classified as a handle and pull in decorative hardware and moldings, so it is intended to serve as the working grip on cabinet doors and drawers.
The manufacturer is Schaub and Company, so this pull aligns with other Schaub decorative hardware pieces when building a coordinated cabinet hardware layout.
The 5 inch center-to-center layout lets this pull fit doors or drawers already drilled on a 5 inch pattern, which simplifies swapping existing handles to this model.
The Schaub Haniburton pull 5 inch CC fits cabinet and drawer fronts that use a 5 inch center-to-center drilling pattern, so it drops into layouts built on that spacing. The polished nickel finish delivers a bright, coordinated metal look across visible hardware, supporting consistent appearance on multi-unit runs. With #8-32 thread or screw size at the mounting points, it mates with common cabinet machine screws for a solid attachment. For projects built around decorative handles and pulls, this Schaub and Company piece provides a defined grip location that suits everyday cabinet operation.