Schaub Haniburton appliance pull describes an appliance-rated handle that is built for appliance fronts where a pull with appliance-style mounting is needed. The pull is identified as an appliance pull in the description, so it is intended for use on appliance panels rather than standard cabinet doors in typical installations. The Web Description specifies an 18 inch center-to-center dimension, which spaces the mounting holes 18 inches apart and sets the visual scale on wider appliance panels. That same description lists a 1/4-20 thread or screw size, so the pull accepts 1/4-20 machine-thread fasteners that match common appliance mounting points. The finish is stated as satin brass, giving the pull a muted brass tone that reads as decorative hardware in visible appliance installations.
The Web Description notes an 18 inch center-to-center dimension, so installers can lay out two mounting points spaced exactly 18 inches apart to match the pull. That fixed spacing directly affects drilling patterns on appliance panels and any templates used on site. The specified 1/4-20 thread or screw size means the handle is built to accept 1/4-20 machine-thread fasteners, which ties directly into how the pull seats against the panel when tightened. Because the product is described as satin brass, the finish choice influences how the pull visually fits among other satin brass pulls or knobs when mounted in the same run.
The SAP Description and Web Description both refer to the product as an appliance pull, which points to use on appliance fronts where a substantial handle style is applied to a door or drawer panel. The 18 inch center-to-center measurement makes this pull suitable for wider front surfaces, since the mounting points are spread over a longer span than small cabinet pulls. Because the category lists Decorative Hardware and Moldings and the product class lists Handles and Pulls, this piece sits within a decorative hardware family used in visible areas of a project. The satin brass finish mentioned in the Web Description gives the pull a brass-toned surface that coordinates with other satin brass decorative hardware when used across an appliance and nearby cabinets.
The clearly stated 18 inch center-to-center dimension allows installers to base drilling templates and layout lines on a single known measurement, which helps keep multiple appliance pulls aligned when several fronts share the same hardware. The Web Description also calls out a 1/4-20 thread or screw size, so installers can match the pull to 1/4-20 fasteners that pass through the appliance panel, helping the handle seat firmly when tightened from the rear side. Knowing that the finish is satin brass lets planners specify this exact pull when they need the same satin brass tone on replacement or additional units in a run. The Brand entry listing Schaub and Company ties the pull to a recognized decorative hardware manufacturer, which helps projects remain consistent when selecting other Schaub handles and pulls to sit visually near this appliance pull.
The Schaub Haniburton appliance pull uses an 18 inch center-to-center measurement, which sets the spacing for the two mounting holes on the appliance front.
The appliance pull is described with a 1/4-20 thread or screw size, so it is designed for use with 1/4-20 machine-thread fasteners at each mounting point.
The 483-SB Haniburton appliance pull has a satin brass finish, providing a brass-toned appearance that coordinates with other satin brass decorative hardware.
This product is categorized under Decorative Hardware and Moldings and further as Handles and Pulls, placing it among visible decorative pulls for finished projects.
The satin brass appliance pull is listed under the brand Schaub and Company, aligning it with other Schaub decorative handles and pulls.
The manufacturer part number 483-SB identifies this specific Haniburton appliance pull configuration, aiding repeat ordering when the same satin brass model is required.
The Web Description defines this product as an appliance pull with an 18 inch center-to-center layout, satin brass finish, and 1/4-20 thread or screw size, so it suits projects that call for appliance-style pulls with those exact dimensions and finish. The Schaub and Company branding and the Decorative Hardware and Moldings, Handles and Pulls classifications present it as a decorative appliance handle choice when coordinating with other Schaub hardware. For projects needing an 18 inch center-to-center satin brass appliance pull built around a 1/4-20 thread standard, this model provides those specific characteristics in one part.