Paramount Extrusions aluminum pull provides a continuous 72 inch (1829 mm) gripping surface, so one piece spans long cabinet or fixture runs where a short handle would break up the line. The 6 foot length matches the SAP description, so installers can plan pulls and cuts against a known stock size. The pull is made from extruded aluminum, which creates a consistent profile along its full length, so each cut section keeps the same feel and look across multiple doors or panels. The finish is aluminum, so the surface presents a uniform metal appearance that coordinates with other aluminum hardware in the same area. A projection of 1-3/4 inch sets the pull out from the face enough for fingers to wrap behind, so users can grab it comfortably on tall doors or large drawer fronts.
The pull is not pre-drilled for mounting, which lets installers determine hole locations based on door stile width, rail positions, or existing hole layouts. The 72 inch length provides room to cut to exact center-to-center requirements, so one bar can yield several pulls with consistent spacing. A projection of 1-3/4 inch creates a fixed stand-off from the door or panel face, so drilling depth and fastener selection can be planned around that known offset. The extruded aluminum construction keeps the profile uniform along the full bar, so any cut section will receive mounting holes in the same cross-sectional zone without surprises.
The 72 inch (1829 mm) overall length positions this Paramount Extrusions aluminum pull for tall cabinet doors, wide storage panels, or multiple smaller doors cut from a single bar. Because it belongs to the Handles and Pulls category within decorative hardware and moldings, it suits jobs where a visible linear pull doubles as a design element on casework. The aluminum finish makes the pull a logical choice for projects already using aluminum trim or moldings, keeping the hardware family consistent. The 1-3/4 inch projection sets the handle off the face enough that users can operate tall wardrobe or pantry doors without fingers rubbing the surface. The 6 foot dimension, reflected in the SAP description and part identity, also means long display fixtures or cabinets can carry an uninterrupted pull line using one continuous piece.
The extruded aluminum material produces a repeatable profile along the whole 72 inch bar, so installers cutting multiple pieces for a run of cabinets get identical cross-sections, which simplifies alignment across doors. The pull being not pre-drilled for mounting allows hole locations to be laid out consistently from the same reference edges on each panel, supporting uniform hardware lines across a room. The known 1-3/4 inch projection stays constant on every cut piece, so clearances between doors, adjacent walls, or neighboring hardware can be calculated once and applied across the project. The manufacturer part number 5090-6A ties these details to a specific Paramount Extrusions handle, which helps shops reorder the exact same profile when adding new cabinets to an existing installation. As part of the Handles and Pulls, Paramount Extrusions class, this pull naturally aligns with other components in the same family when a coordinated hardware set is required.
The Paramount Extrusions aluminum pull has an overall length of 72 inches (1829 mm), which allows spanning tall doors or cutting several shorter cabinet pulls from one piece.
The 5090-6A pull is made from extruded aluminum, giving a consistent profile along its 6 foot length for uniform appearance on multiple doors or drawer fronts.
The aluminum pull has a projection of 1-3/4 inch, spacing the grip away from the door or panel surface to give hand clearance during everyday operation.
The 72 inch aluminum pull is not pre-drilled for mounting, so hole locations can be laid out to match specific door sizes or existing mounting patterns.
The pull has an aluminum finish, matching the aluminum material so it coordinates cleanly with other aluminum decorative hardware and moldings on the same project.
The 6 foot length allows one Paramount Extrusions aluminum pull to serve long doors or yield multiple shorter pulls, supporting consistent hardware lines across wide cabinets.
The Paramount Extrusions aluminum pull in 72 inch (1829 mm) length offers a straightforward way to cover tall doors or create multiple matching handles from one bar. The extruded aluminum material and aluminum finish keep the profile consistent, which matters when lining up pulls across cabinets or fixtures. With a 1-3/4 inch projection and no pre-drilled holes, the pull adapts to varied door sizes and mounting layouts. For projects calling for a 6 foot aluminum handle profile from Paramount Extrusions Company, this 5090-6A pull through Wurth Baer Supply aligns cleanly with that requirement.
Sold In: 1 Each