2.8 Gallon Pressure Pot Gasket describes this Binks replacement tank gasket designed for 2.8 gallon PT Series ASME tank models, so it restores the seal at the tank lid and keeps the pressure system working as intended in your spray setup. The Santoprene gasket is specified for Binks PT-33-1, giving you a direct part number match when you are servicing existing Binks pressure tanks. Its square shape gasket design is built to sit flat in the tank groove, which helps maintain even contact around the full circumference of the tank opening. Approximate outside diameter of 10-3/8 inches and inside diameter of 9-3/8 inches position the sealing surface correctly on 2.8 gallon PT Series tanks. The 1/2 inch width gives the gasket enough surface area to seat securely, helping reduce air loss and pressure drop during spraying tasks.
The approximate outside diameter of 10-3/8 inches and inside diameter of 9-3/8 inches place this Binks PT-33-1 gasket precisely on the 2.8 gallon PT Series tank lip, so the lid compresses the gasket where the tank was designed to seal. The square shape gasket profile helps it sit squarely in the groove or seating surface, which matters when you are tightening the lid and relying on an even seal around the full circle. With a 1/2 inch width, the gasket offers enough material between inner and outer edges to distribute load, helping the gasket maintain contact under working pressure. This dimensional match lets installers swap the part during service without altering the tank or lid components.
This 2.8 Gallon Pressure Pot Gasket is described as fitting PT Series ASME tank models 83C-210, 83C-220, 83C-211, 83C-221, 83Z-210, 83Z-220, 83Z-211, 83Z-221, and 4YP11 1ZLB6, so it targets a defined group of Binks 2.8 gallon pressure tanks. The product name "Replacement Tank Gaskets PT-33-1 - Binks PT-33-1" ties the gasket directly to Binks-branded spray equipment in the pressure tank category, helping technicians align it with existing PT Series hardware in finishing shops. Being listed under spray equipment and pressure tanks indicates its role at the tank lid interface, where maintaining pressure is important for stable material delivery. When these identified PT Series tanks are in service, matching the model numbers to this gasket supports straightforward part selection during scheduled maintenance or repairs.
The approximate outside diameter of 10-3/8 inches, inside diameter of 9-3/8 inches, and 1/2 inch width give this Binks PT-33-1 gasket a clearly defined sealing footprint, which helps produce consistent seating when the lid clamps onto a 2.8 gallon PT Series tank. Its square shape gasket description indicates straight outer and inner edges, so it nests predictably in the tank or lid recess, aiding repeatable alignment each time the tank is opened and closed. The Santoprene material called out in the SAP description, combined with the defined dimensions, positions this gasket as a purpose-built sealing component for pressure tank use rather than a generic ring. Within regular repair and replacement workflows, these fixed dimensions and the PT-33-1 identifier allow installers to replace worn gaskets with a part that matches the original design intent.
This Binks PT-33-1 gasket is described as a 2.8 Gallon Pressure Pot Gasket, so it is intended for sealing 2.8 gallon PT Series pressure tanks during operation.
This gasket fits PT Series ASME tank models 83C-210, 83C-220, 83C-211, 83C-221, 83Z-210, 83Z-220, 83Z-211, 83Z-221, and 4YP11 1ZLB6, matching those specific Binks pressure tanks.
The gasket has an approximate outside diameter of 10-3/8 inches, an inside diameter of 9-3/8 inches, and a width of 1/2 inch, defining its sealing area on the tank.
The SAP description lists this as "GASKET, 2.8GAL SANTOPRENE," indicating a Santoprene gasket for these 2.8 gallon PT Series pressure tanks.
The square shape gasket description indicates straight edges that seat evenly in the tank or lid groove, promoting uniform compression and a consistent seal around the tank opening.
The PT-33-1 part number links directly to Binks PT Series 2.8 gallon tanks, giving technicians a clear identifier when ordering or stocking replacement gaskets.
This Replacement Tank Gaskets PT-33-1 - Binks PT-33-1 part ties directly to 2.8 Gallon Pressure Pot Gasket use on defined PT Series ASME tank models, so it aligns with existing Binks pressure equipment in finishing shops. The stated Santoprene construction, square shape gasket form, and approximate 10-3/8 inch by 9-3/8 inch by 1/2 inch dimensions together define how it seats on these 2.8 gallon tanks. For shops maintaining Binks PT Series tanks, matching the PT-33-1 identifier and listed model numbers helps keep pressure pots sealing consistently during spraying tasks.
Sold In: 1 Each