Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Little Hand XL Support System is a Fastcap upper jack designed to hold upper wall cabinets in place when base cabinets are not installed, so a single installer can position cabinets while fastening them without extra lifting during that stage of the job.
This 3-H LITTLE jack extends from a fully closed 16-1/2 inch position to a fully opened 22-3/4 inch position, which lets you work effectively in the low height range often needed for upper cabinets over counters or work surfaces where only a short temporary support fits between the surface and the cabinet.
The system is part of Wurth Baer Supply material handling offerings, so it fits into a professional shop setup focused on woodworking tasks where controlled cabinet positioning improves workflow and repeatability during install runs.
Each single jack is rated to support up to 150 lb, which allows it to hold a typical upper cabinet section during mounting, keeping the load stable at height while fasteners are driven from the installer side.
The top and bottom feet measure 6 inches by 6 inches and are fixed, so the load spreads over a larger contact area at both ends, helping the jack bear cabinet or ceiling pressure without concentrating force on a small point.
The extension from 16-1/2 inch to 22-3/4 inch defines the working height of this cabinet jack, so any task that falls within that short vertical span can use the tool as a bracing post to hold an upper cabinet bottom at the intended level relative to a lower surface.
The ergonomic pump handle operates in 1/2 inch increments, which gives you stepped control when raising or lowering the load inside that range, allowing fine-tuned adjustment for cabinet alignment to marks on the wall or to neighboring cabinets.
Because the top and bottom feet are fixed at 6 inches by 6 inches, the contact geometry stays consistent as you adjust height, so once the jack is placed under the cabinet and extended, the wide feet continue to provide stable bearing surfaces during final positioning.
This combination of a defined low extension range, incremental pump adjustment, and fixed wide feet turns the jack into a repeatable setup tool for similar cabinet runs where you often work at comparable heights and want consistent results.
The Fastcap Little Hand XL Support System is defined as an upper jack system for hanging upper wall cabinets when base cabinets are not in place, so it fits jobs where you still need to mount uppers before installing bases or counters below.
With its 16-1/2 inch fully closed height, the jack suits situations where a short support is needed between a floor-built platform, temporary stand, or existing surface and the underside of an upper cabinet that is being lifted into final position within that low vertical range.
The 22-3/4 inch fully opened position sets the maximum cabinet elevation this support can achieve in one setup, which is effective when the desired underside height falls inside that span, allowing the jack to hold the cabinet while alignment and fastening happen.
The 150 lb single-jack support capacity means it can reliably hold many common upper cabinet sections during use, matching the typical weight range of wood cabinets and similar casework pieces that installers handle in woodworking and shop environments.
Because the top and bottom feet are each 6 inches by 6 inches and fixed, they provide broad footing on floors, counters, or platforms while also creating a larger bearing surface against the cabinet bottom or structural surface above, supporting solid contact on both interfaces.
The product sits in Wurth Baer Supply material handling offerings, placing it among shop and safety supplies used by woodworking professionals who want controlled cabinet handling rather than manual lifting only.
The ergonomic pump handle that adjusts the jack in 1/2 inch increments gives installers predictable steps for raising a cabinet, so once a preferred increment pattern is known for a given layout, that same sequence can be repeated across similar runs.
Because each pump change moves the support by a defined 1/2 inch, the installer can count strokes to reach a target mark, which helps maintain consistent reveal heights under cabinets or uniform gaps to soffits when working within the 16-1/2 to 22-3/4 inch range.
The fixed 6 inch by 6 inch feet mean every setup uses the same size contact area, so once you understand how that footprint behaves on your typical surfaces, you can position the jack confidently for similar cabinet sizes without recalculating contact conditions each time.
The 150 lb capacity rating on a single jack clarifies how much weight it is intended to support, which helps plan workflow for handling upper cabinet sections that fall within that range, improving predictability around how the jack will behave as you fasten the box.
Using a defined extension span instead of an open-ended pole keeps the jack focused on shorter support tasks, which can streamline how installers approach recurring cabinet heights that match the 16-1/2 to 22-3/4 inch adjustment window within material handling workflows.
As part of a labeled upper jack system for wall cabinets, the Little Hand XL fits directly into cabinet hanging stages, supporting a methodical sequence: rough placement, pump-driven fine adjustment in half-inch steps, and final securing while the support holds the weight.
The Little Hand XL Support System is an upper jack designed to make hanging upper wall cabinets easier when base cabinets are not in place, holding cabinets during positioning and fastening.
The jack extends from 16-1/2 inch in the fully closed position to 22-3/4 inch in the fully opened position, covering short vertical gaps in that range during cabinet installation tasks.
A single Little Hand jack can support up to 150 lb, allowing it to hold many standard upper cabinet sections while they are aligned and fastened to the wall.
The ergonomic pump handle adjusts the jack in 1/2 inch increments, providing controlled, step-by-step height changes for precise cabinet alignment within the available extension range.
The top and bottom feet are 6 inches by 6 inches and fixed, spreading the load over a wider area at both ends to help stabilize the cabinet and the supporting surface.
This jack is part of Wurth Baer Supply material handling products, serving woodworking and cabinet installation tasks where controlled cabinet support improves workflow.
The Little Hand XL Support System from Fastcap, with its 16-1/2 to 22-3/4 inch extension range, 150 lb capacity, and 6 inch by 6 inch fixed feet, offers a defined way to brace upper wall cabinets during installation when base units are not present.
The ergonomic pump handle adjusting in 1/2 inch increments supports precise height changes within that span, helping align cabinets accurately while the jack from Wurth Baer Supply holds the load.
Select this upper jack when your cabinet handling work calls for a short-range, controlled vertical support that fits directly into shop and jobsite material handling routines.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Package |  FA3HLITTLE-2PCSYST Mfr# 3-H LITTLE 2PC SYS | 3rd Hand Short Support System, 16-1/2" to 22-3/4" Extension - Fastcap 3-H LITTLE 2PC SYS |