Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Fastcap Little Hand support system is a short upper jack designed to make hanging upper wall cabinets easier when base cabinets are not in place, so cabinets can be positioned before any lower casework is installed. This 3rd Hand Short Support System extends from 16-1/2 inches in the fully closed position to 22-3/4 inches in the fully opened position, covering common distances between a bench, floor, or temporary surface and the underside of wall cabinets. A single jack can support up to 150 lb, holding cabinet weight while fasteners are installed, which reduces the need for a second person during the lift. Top and bottom feet are 6 inch by 6 inch in a fixed position, so the load spreads over a broad area on both contact points for stable support against cabinets, ceilings, or floors.
The Little Hand upper jack system uses an ergonomic pump handle that adjusts the jack in 1/2 inch increments, so cabinet height can be raised or lowered in small, repeatable steps during layout. Because the extension range is 16-1/2 inches in the fully closed position to 22-3/4 inches in the fully opened position, the tool fits under upper wall cabinets in short spans, such as when working off a temporary platform, cart, or countertop height mock-up. The 6 inch by 6 inch fixed-position feet at the top and bottom give a broad, stable contact surface that supports up to 150 lb on a single jack, allowing the load to stay steady while fasteners are driven.
The 3rd Hand Short Support System is described as the Little Hand upper jack system, and it is designed to make hanging upper wall cabinets easier when base cabinets are not in place, so it fits well in new construction or remodel stages before bases are set. With an extension range from 16-1/2 inches fully closed to 22-3/4 inches fully opened, it works in tighter vertical spaces, such as when supporting cabinets from a temporary platform or from low surfaces in a shop or job trailer. The single jack support capacity of up to 150 lb means it can hold many individual upper wall cabinets within that weight range while layout marks are transferred and fasteners are driven. Because the top and bottom feet are 6 inches by 6 inches in a fixed position, the tool can press against cabinet bottoms, soffits, or framing surfaces with a broad pad, helping stability during positioning.
The ergonomic pump handle on this upper wall cabinet support tool adjusts the jack in 1/2 inch increments, giving installers control of cabinet height in small, predictable steps, which supports precise alignment with adjacent cabinets, trim, or ceiling lines. The defined extension range of 16-1/2 inches to 22-3/4 inches sets clear working limits, so installers know the jack is intended for short support situations rather than full floor-to-ceiling spans, which helps select it for the right stage of the job. The ability of a single jack to support up to 150 lb lets one person hold a cabinet at working height while fastening, reducing manual lifting strain during the process. The 6 inch by 6 inch fixed-position feet at top and bottom offer ample support, spreading contact over a larger area so the jack seats solidly against cabinets or structural surfaces while carrying the load.
The Little Hand upper jack system extends from 16-1/2 inches in the fully closed position to 22-3/4 inches in the fully opened position, covering short-span cabinet support situations.
A single Little Hand jack can support up to 150 lb, so it can hold many individual upper wall cabinets during positioning and fastening within that load range.
The ergonomic pump handle adjusts the jack in 1/2 inch increments, allowing controlled cabinet height changes so installers can fine-tune reveals and alignment without large jumps.
The top and bottom feet are 6 inches by 6 inches in a fixed position, giving a broad contact area that helps stabilize the jack against cabinets, floors, or ceilings.
This Little Hand upper jack system is designed to make hanging upper wall cabinets easier when base cabinets are not in place, supporting installation during earlier project stages.
The designation Fastcap 3-H LITTLE 2PC SYS identifies this product as part of Fastcap's 3rd Hand Little Hand system line within their material handling offerings.
The 3rd Hand Short Support System from Fastcap is a Little Hand upper jack tool designed to make hanging upper wall cabinets easier when base cabinets are not in place, so it fits cabinet installers and serious woodworkers handling overhead work. With a 16-1/2 inch to 22-3/4 inch extension range, an ergonomic pump handle that adjusts height in 1/2 inch increments, 6 inch by 6 inch fixed-position feet, and a single jack capacity of up to 150 lb, it provides controlled short-span support. For jobs that demand a compact, repeatable cabinet support system, this Fastcap 3-H LITTLE 2PC SYS offers a defined set of working capabilities.
Sold In: 1 Package
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  FA3-HAND-15.7HD Mfr# 3-H LITTLE | Little Hand XL™ Support System, 16-1/2" - 23-1/2" Extension |