3 inch traditional cup pull describes a solid brass cabinet handle from Schaub and Company designed for a 3 inch center-to-center drill pattern, so it suits standard cabinet layouts and lets existing hole spacing stay usable during upgrades or replacements. The overall 3-3/4 inch length covers older screw marks around the bores, helping fronts look clean after swap-outs. Its oil rubbed bronze finish gives a dark, traditional appearance that supports classic kitchen, bath, or furniture styling where warmer metal tones are preferred. Solid brass material builds strength into the pull body, supporting repeated daily use on frequently opened doors and drawers. A 1 inch projection positions fingers away from the cabinet face, creating clearance that reduces knuckle rubbing on deeper drawers. The 1-1/4 inch width provides a full front edge to grab, which helps on heavier loads or wider drawer faces.
This Schaub and Company solid brass cup pull is specified for a 3 inch center-to-center spacing between fastener points, so it matches cabinets already bored at 3 inches and keeps drill jigs simple for new work. The 3-3/4 inch overall length surrounds those mounting points, giving a clear visual reference for alignment along rails or drawer fronts. A 1 inch projection establishes the standoff from the cabinet face, guiding installers when they position pulls in tight corridors where overhang matters. The 1-1/4 inch width defines the vertical footprint on the face, which helps with consistent vertical spacing from top edges on drawer fronts. Screw size is specified as 8-32 x 1 inch, so the threaded interface is known when matching to standard cabinet fastening practices.
The 3 inch center-to-center layout makes this traditional cabinet cup pull a practical match for many existing residential and light commercial cabinets that already use that drilling pattern, so banks of drawers can be updated without redrilling the faces. A 3-3/4 inch overall length gives it enough span to sit proportionally on typical drawer widths, from smaller kitchen drawers to medium bath or office storage. The oil rubbed bronze finish suits traditional or transitional designs where a dark metal accent is preferred, so it coordinates well with stained wood and many painted colors. Because the pull is made from solid brass, it brings metal mass appropriate for everyday cabinet use in areas like kitchens, work rooms, or built-ins. The 1-1/4 inch width and 1 inch projection build a compact but functional profile that fits on face frames or slab fronts without overwhelming the panel.
The specified 3 inch center-to-center spacing allows installers to use standard drilling jigs, which supports consistent alignment from one drawer front to the next across long cabinet runs. That known spacing also simplifies layout when mixing this Schaub and Company pull with other 3 inch center hardware in the same room. The 3-3/4 inch length provides clear end references against cabinet edges or layout marks, helping keep pulls level and evenly positioned. With a 1 inch projection, the face of the pull sits at a predictable distance from the cabinet, which matters when planning clearances near opposing doors or side walls. The 1-1/4 inch width defines a repeatable vertical mounting footprint that helps maintain equal reveals from the top edge on stacked drawers. Solid brass construction contributes to consistent thread engagement with the 8-32 screws, supporting a firm mount that remains stable through daily handling.
This cup pull uses a 3 inch center-to-center spacing between mounting points, so it matches cabinets and drawers laid out for that standard drill pattern.
The pull has a 3-3/4 inch length, a 1 inch projection from the cabinet face, and a 1-1/4 inch width, which defines its footprint on the door or drawer front.
This Schaub and Company cabinet pull is made from solid brass, which gives the handle a metal construction suited to frequent door and drawer use.
The traditional cup pull has an oil rubbed bronze finish, providing a dark, classic appearance that coordinates with many stained and painted cabinet styles.
This cabinet pull is specified with 8-32 x 1 inch screws, so the threaded connection matches common cabinet hardware fastening dimensions.
This cup pull is manufactured by Schaub and Company, identified by part number 730-10B, which helps match it to other items in the Traditional Series.
This 3 inch traditional cup pull from Schaub and Company combines solid brass construction, an oil rubbed bronze finish, and a 3 inch center-to-center layout, so it fits standard cabinet drilling while delivering a classic look. The 3-3/4 inch length, 1 inch projection, and 1-1/4 inch width create a compact yet functional grip for everyday doors and drawers. With defined dimensions and 8-32 x 1 inch screw sizing, this Traditional Series pull is ready for cabinet, vanity, or furniture projects that call for matched hardware across multiple fronts.